ADEMCO VISTA-128B Guia de preparacion Pagina 159
- Pagina / 252
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Section 23 - #93 Menu Mode Programming
23-21
*Notes: This factory-provided vocabulary of words is subject to change.
Bulleted words in bold face type are those that are also available for use by the 4285/4286 VIP
Module. If using a VIP Module, and words other than these are selected for alpha descriptors, the
Voice Module will not provide annunciation of those words.
Device Programming
This menu is used to program keypads, receivers and relay modules.
From Data Field Programming Mode, press #93 to display "ZONE PROG?". Press 0
repeatedly to display "DEVICE PROG?".
DEVICE PROG?
1=YES 0=NO
Press 1 to enter Device Programming.
DEVICE ADDRESS
01-31, 00=QUIT
The device address identifies the device to the control. Enter
the 2-digit device address number to match the device's
physical address setting (01-30).
Press
[∗] to accept entry.
Note: Device Address 04 must be used for the 4285/4286 Voice
Module, if one is utilized. If not, it can be used for another
device type.
Device Address
00
is always set as an alpha keypad assigned to Partition 1 with no sounder
suppression options, and these settings cannot be changed.
DEVICE TYPE
Select the type of addressable device as follows:
0 = device not used
1 = alpha keypad (6139/6139R)
3 = RF receiver (5881)
4 = output relay module (4204)
5 = voice (VIP) Module (4285/4286)
6 = long range radio
9 = Vista Gateway Module (VGM)
Press [∗] to accept entry.
Alpha Keypad
CONSOLE PART.
If device type 1 (alpha keypad) is selected, this prompt will
appear. Enter the addressable device's default partition
number (01 to maximum number of partitions programmed for
system in field 2*00). This is the primary partition for which
the device is intended to be used. Enter 9 to make this keypad
a "Master" keypad for the system.
Press [∗] to accept entry.
- VISTA-128B 1
- K3500-3 7/98 2
- Table of Contents 9
- List of Figures 14
- How To Use This Manual 15
- General Description 17
- Wireless 18
- Zone Expansion 18
- Planning a Partitioned System 23
- Common Lobby Logic 24
- MAIN ENTRANCE 25
- OFFICE #1 OFFICE #2 25
- COMMON LOBBY 25
- Codes with Global Arming 26
- Codes with Non-Global Arming 26
- Cross-Zoning 30
- Call Waiting Defeat Logic 31
- Installing The Control 33
- Installing The Keypads 37
- Figure 5-2 38
- #93 Menu Mode 39
- Basic Hardwired Zones 001-009 41
- Figure 6-3 43
- DISARMED 45
- READY TO ARM 45
- DISARMED Press 46
- 2-Wire Polling Loop Expansion 47
- (Zones 010 - 128) 47
- Wire Gauge Max. Length 48
- #22 gauge 650 feet 48
- #20 gauge 950 feet 48
- #18 gauge 1500 feet 48
- #16 gauge 2400 feet 48
- Power Up Procedure 49
- Extension Loop #1 50
- Extension Loop #2 50
- Extension Loop #8 50
- Wireless Zone Expansion 55
- Relay Outputs and 63
- Powerline Carrier Devices 63
- Relay Programming 66
- #93 Menu Mode 66
- 4285/4286 VIP Module 67
- Mounting the VIP Module 68
- Wiring the VIP Module 68
- 1 23456 7 69
- 4 3 2 1 73
- The Mechanics of 74
- Programming 74
- J7 Trigger Outputs 75
- Ground Start Trigger Setup 76
- The Mechanics o 77
- 1 2 3 4 5 6 7 8 9 78
- Event Log Printer Connections 82
- 7820 Long Range Radio 83
- Wiring the Long Range Radio 84
- Trouble Messages 85
- Access Control 87
- Access Control Dialer Events 90
- External Sounders 91
- Alarm Output Supervision 92
- Wiring the Alarm Output 93
- Programming the Alarm Output 94
- Event Log Options 95
- Supplied with 96
- Programming Event Log Options 97
- Event Logging Procedures 97
- CLEAR EVENT LOG 99
- 0=NO 1=YES 99
- 0=NO 1=YES 99
- 4100APG Pager Interface 101
- Wiring the 4100APG 102
- 4100APG LED Indications 104
- Final Power-Up Procedure 105
- 4142TR CABLE 106
- Cannot exceed 128MA 107
- Connecting The Battery 109
- The Mechanics of Programming 111
- Viewing Data Fields 112
- Entry Errors 112
- #93 Menu Mode Programming 114
- Zone Type Definitions 115
- Zone Index/Zone Type Defaults 119
- Zone Type Defaults 120
- Data Field Descriptions 121
- 95 96 99 122
- 95 96 99 Duress 129
- Enter 00-09; B-F (11-15) 130
- [15 15 15 15] 130
- Alm Chck Byps O/C Systm Test 134
- F B S 137
- Zone Programming 141
- 010 LEARN S/N? 145
- 1 = YES, 0 = NO 1 145
- Sequential Mode Programming 147
- Zone Number Entered 148
- 010 INPUT S/N 149
- A 022-4064 149
- Serial # 149
- 010 CONFIRMED SL:1 149
- A022-4064 149
- REPORT CODE PROG 150
- 1 = YES 0 = NO 0 150
- QUIT REPORT MENU 154
- 1 = YES 0 = NO 0 154
- QUIT MENU MODE? 154
- 1 = YES 0 = NO 0 154
- Relay Voice Descriptors 158
- Device Programming 159
- SOUND OPTION 160
- KEYPAD GLBL? 160
- RF EXPANDER 160
- HOUSE ID XX 160
- SUPERVISED CF? 160
- SPACE ENTER 161
- MODULE PART 163
- Zone List Programming 168
- RF Serial Number Clear Mode 171
- CLEAR RF SERIAL#? 172
- 1 = YES, 0 = NO 0 172
- ARE YOU SURE? 172
- 1 = YES, 0 = NO 0 172
- Scheduling Options 173
- Time Window Definitions 175
- Open/Close Definitions 176
- Scheduling Menu Mode 178
- Scheduling Menu Structure 179
- Time Windows 180
- Daily Open/Close Schedules 181
- Holiday Schedules 182
- Time-Driven Events 183
- Relay No. if 4204 relays 185
- Timed Events ? 185
- 1 Yes 0 = No 0 185
- TIMED EVENT # ? 185
- 01-20, 00=Quit 01 185
- 50=Off-normal Reminder 187
- Temporary Schedules 189
- User Scheduling Menu Mode 191
- In This Section 193
- A Successful Transmission 194
- Reporting Formats 194
- Downloading Primer 205
- On-Line Control Functions 207
- Access Security 207
- PRINTER DTR 208
- Setting The Real-Time Clock 209
- User Access Codes 211
- OK TO DELETE 003? 217
- 0=NO 1=YES 217
- Keypad Functions 219
- ARM ALL ? 220
- 0 = NO , 1 = YES 220
- Closing Delay ? 221
- Hit 0-2 Hours 221
- Part. 1 A0 222
- User 01 Auth.=1G 222
- ENTER SPEED KEY # 223
- 01-32 00=QUIT 223
- ENTER DEVICE NO 224
- 00=QUIT 01 224
- HIT THE "*" KEY 225
- HIT 0=OFF , 1=ON 225
- Testing The System 227
- Armed Burglary System Test 228
- Trouble Conditions 228
- To the Installer 230
- Regulatory Agency Statements 231
- Requirements 232
- DIP Switch Tables 235
- 4275 PIR 237
- 4194 REED CONTACT 237
- (SURFACE MOUNT) 237
- 4278 PIR 237
- Summary of System Commands 239
- Specifications 241
- WARNING! 249
- ¬.l 251
- Copyright 252
- 1998 PITTWAY CORPORATION 252
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-128B
Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS Especificaciones
(128 paginas)
(128 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-20HW Guía para resolver problemas
(100 paginas)
(100 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-10SE Manual de usuario
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales