ADEMCO Vista 4130XT Manual de instrucciones descargar pdf (Pagina 77)

4. Wiring Run Permitted to No. 4208 Zone Expander (or other

VECTOR RPMS):

Wire Gauge

Max. Wire Run

22 (0.64 mm O.D.) 650 ft (200 m)

20 (0.81 mm O.D,) 950 ft (290 m)

18 (1.0 mm O.D.) 1500 ft (460 m)

16 (1 3 mm O.D.) 2400 ft (730 m)

CABINET MOUNTING THE 4130XT

In buildings using concrete, cinder block or brick wall construction, the

4130XT Security Control can be installed in a wall-mounted metal

cabinet. This cabinet, which measures 8“ (20. 3 cm) W x 8“ (20.3 cm) H

x 2“ (5 cm) D, is available under part No, 4134-8. The 4130XT Control is

mounted in a cut-out in the door of the cabinet, with the function keys,

LEDs and display accessible. The back-up battery is installed within the

cabinet Also available for use within the cabinet are connector blocks

with which the 4130XT’S flying leads can be tied to the interface wiring

(from protection zones, etc.). See Diagram B.

Mounting the 4130XT in the Cabinet

Note that there is a mounting flange on each side of the opening m the

cabinet door.The Control is secured to these flanges with the two self-

tappmg screws supphed. Positton the Control (wtlh back cover removed)

in the opening and secure as follows, referring to Diagram A.

On the left-hand side, insert the No. 6 x 1” self-tapping screw through the

front of the Control into the left flange as shown, and secure. Do not fully

t!ghten yet.

To secure the right-hand .wde, mserf the No, 4 x %“ self-tapping screw

into the other flange from the rear. and screw into the slot in the plastic

4208 ZONE EXPANDER

Physical: Width

3-7/8” (9.8 cm)

Height:

7“(178 cm)

Depth:

1-3/8” (3.5 m)

2. Electrical:

Voltage Input

8-11 Volts

(w/l KHz

Modulation)

Current Drain: 16 mA

at the rear of the Control, as shown, Making sure the Control is straight,

tighten this screw fully,

Fully tighten the screw on the other side, then insert the VISTA XT name-

plate into the recess to cover the screw, as shown in Diagram A.

Mounting Cabinet on Wall:

Four holes have been prowded m the back of the cabinet for mounting

purposes -2 keyhole slots at the top and 2 holes at the bottom. Knock-

outs are prowded at the sides [% “(2.2cm) diameter], plus one at the rear

[1 -%” (4.5 cm) diameter].

1. If the interface wiring is being brought through the wall, make the

required opening In the wall for the wmrig.

2. Remove the desired knockout m the cabinet to allow entry of the inter-

face wiring.

3. Place the cabinet on the wall m the desired position and mark the loca-

tions of the mounting holes.

Note The cabinet may be mounted with only 2 screws at the keyhole

slots, if desired.

4. Drill mounting holes in the wall and insert anchors. Mounl the cabinet

securely to the wall with four (or 2) screws.

1 2 ... 72 73 74 75 76 77 78 79 80 81 82 83 84

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista 4130XT Manual de instrucciones Pagina 77

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista 4130XT