ADEMCO Vista-32FB Guia de preparacion

K3521V4 10/09 Rev A VVVVVVVVIIIIIIIISSSSSSSSTTTTTTTTAAAAAAAA SSSSSSSSEEEEEEEERRRRRRRRIIIIIIIIEEEEEEEESSSSSSSS VVVVVVVVIIIIIIII

VISTA-32FB Installation and Setup Guide x Program feature or option Permitted in UL864? Y/N Possible settings Settings permitted in UL 864 ✱27 TEST

VISTA-32FB Installation and Setup Guide 9-2 Level 6: Duress Codes • Sends a silent alarm to a central monitoring station if the user is being force

Section 9 – User Access Codes 9-3 Adding a Master, Manager, or Operator Code Enter Installer Code†+ [8] + new user no. (02-75) + new user’s code †Or M

VISTA-32FB Installation and Setup Guide 9-4 Changing a Master, Manager, or Operator Code Enter Installer Code*+ [8] + new user no. (02-75) + new use

10-1 SECTION 10 Testing the System ••••••••••••••••••••••••••••••••••••••••••••••••• Battery Test When AC power is present, the VISTA-32FB runs a br

VISTA-32FB Installation and Setup Guide 10-2 PROMPT EXPLANATION AUTO-TEST DET? 0=NO 1=YES Enter 1 (YES) to have the system automatically test al

Section 10 – Testing The System 10-3 Armed Burglary System Test • Alarm messages are sent to the central station during the armed tests. Notify the

VISTA-32FB Installation and Setup Guide 10-4 Trouble Conditions Supervisory Messages Display Description SUPV + Zone Number This indicates that a f

Section 10 – Testing The System 10-5 To the Installer Regular maintenance and inspection (at least annually) by the installer and frequent testing by

VISTA-32FB Installation and Setup Guide 10-6

11-1 SECTION 11 Using the Vista-32FB as a Slave Communicator ••••••••••••••••••••••••••••••••••••••••••••••••• To use the Vista-32FB as a Slave Com

xi Program feature or option Permitted in UL864? Y/N Possible settings Settings permitted in UL 864 1✱28 RF TRANSMITTER LOW BATTERY SOUND N 0 =

VISTA-32FB Installation and Setup Guide 11-2 Sending Vista-32FB System Troubles to the Fire Alarm Panel If using an alpha keypad on the Vista-32FB t

A-1 APPENDIX A Regulatory Agency Statements ••••••••••••••••••••••••••••••••••••••••••••••••• UL Installation Requirements UL This system may be use

VISTA-32FB Installation and Setup Guide A-2 UL609 Local Mercantile Premises/Local Mercantile Safe & Vault 1. All zones must be configured for E

A-3 FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the

VISTA-32FB Installation and Setup Guide A-4 CANADIAN EMISSIONS STATEMENTS This Class B digital apparatus complies with Canadian ICES-003 NOTICE The

B-1 APPENDIX B Summary of System Commands •••••••••••••••••••••••••••••••••••••••••••••••••• User Code Commands Add A User Code = User Code + 8 + Ne

VISTA-32FB Installation and Setup Guide B-2

C-1 APPENDIX C Specifications •••••••••••••••••••••••••••••••••••••••••••••••••• Physical: 18"H X 14-1/2"W X 4.3"D Electrical: Prim

VISTA-32FB Installation and Setup Guide C-2

D-1 APPENDIX D Contact ID Event Codes •••••••••••••••••••••••••••••••••••••••••••••••••• TABLE OF CONTACT ID EVENT CODES Code Definition 110 Fire A

VISTA-32FB Installation and Setup Guide xii Program feature or option Permitted in UL864? Y/N Possible settings Settings permitted in UL 864 2✱18

VISTA-32FB Installation and Setup Guide D-2

Index •••••••••••••••••••••••••••••••••••••••••••••••••• #93 Menu Mode Programming ... 4-2 #93 Menu Mode Programming

Console Input (CS) Type 09... 4-7 Contact ID ...

LINE SEIZE...C-1 List of Figures...

SYSTEM LO BAT ... 10-4 System LoBat”...

WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM While this System is an advanced wireless security system, it does not offer guaranteed protection aga

For the latest warranty information, please go to: www.honeywell.com/security/hsc/resources/wa

2 Corporate Center Drive, Suite 100P.O. Box 9040, Melville, NY 11747Copyright © 2009 Honeywell International Inc.www.honeywell.com/secu

xiii Program feature or option Permitted in UL864? Y/N Possible settings Settings permitted in UL 864 3✱50 ZONE TYPE RESTORE ENABLES FOR TYPES 16-1

VISTA-32FB Installation and Setup Guide xiv

1-1 SECTION 1 General Description ••••••••••••••••••••••••••••••••••••••••••••••••• About the VISTA-32FB The VISTA-32FB is a two-partition, UL Liste

VISTA-32FB Installation and Setup Guide 1-2 System Communication • Provides supervision of the phone lines (main and backup) • Supports the 5140DL

Section 1 – General Description 1-3 Guidelines for Wiring a System The installer must keep certain guidelines in mind while installing a system. The V

VISTA-32FB Installation and Setup Guide 1-4 BLACK -RED +YELLOW DATAGREEN DATABLACK -RED +YELLOW DATAGREEN DATABLACK -RED +YELLOW DATAGREEN DATABLACK

2-1 SECTION 2 Partitioning ••••••••••••••••••••••••••••••••••••••••••••••••• Theory of Partitioning This system provides the ability to arm and disa

ii

VISTA-32FB Installation and Setup Guide 2-2 Common Lobby Logic When an installation consists of a partition shared by users of other partitions in a

Section 2 – Partitioning 2-3 Sequence #1: Office 1 Office 2 Lobby Action User #1: Disarms (Armed) Disarms User #2: (Disarmed) Disarms No Change

VISTA-32FB Installation and Setup Guide 2-4 Master Keypad Setup and Operation Although this system has two actual partitions, it provides an extra p

3-1 SECTION 3 Installing the Control ••••••••••••••••••••••••••••••••••••••••••••••••• This section describes the procedures for mounting and wiring

VISTA-32FB Installation and Setup Guide 3-2 V32FB-004-V0TELCO LINEBATTERYBATTERYXFMRNOT TO SCALEFUSETIE WRAPTO CABINETZONEANDBELLWIRINGMAKE SURE THA

Section 3 – Installing the Control 3-3 Mounting the Control in the Attack-Proof Cabinet (Suitable for Commercial Fire/Commercial Burglary Applications

VISTA-32FB Installation and Setup Guide 3-4 Mercantile Safe and Vault Listing Guidelines • Follow the guidelines given above for Mercantile Premise

Section 3 – Installing the Control 3-5 fire_burg_cab-002-V1PC BOARDPLATECABINETSPACERPLATECABINETDETAIL ASIDE VIEWOF ATTACHMENTDETAIL CSIDE VIEW, PC B

VISTA-32FB Installation and Setup Guide 3-6 Commercial Fire Requirements For commercial fire installations, the primary fire keypad must be installe

Section 3 – Installing the Control 3-7 Installing External Sounders The VISTA-32FB provides two Notification Appliance Circuits. Each circuit is rate

iii . Table of Contents ••••••••••••••••••••••••••••••••••••••••••••••••• General Information ...

VISTA-32FB Installation and Setup Guide 3-8 ALARM INDICATING DEVICE TYPE MANUFACTURER MODEL # 2-Wire Wall Mount Horn/Strobe, 12/24V, Standard Cand

Section 3 – Installing the Control 3-9 Mfg Alarm Indicating Device Type Model Candela Setting Horn Setting Max # of Devices System Sensor Horn, St

VISTA-32FB Installation and Setup Guide 3-10 Mfg Alarm Indicating Device Type Model Candela Setting Horn Setting Max # of Devices System Sensor

Section 3 – Installing the Control 3-11 NOTES: USE NON-POLARIZED INDICATING DEVICES. WIRING IS NOT SUPERVISED. DO NOT EXCEED RATINGS OF THE SUPP

VISTA-32FB Installation and Setup Guide 3-12 Main Dialer Connections To connect the main dialer, refer to the Summary of Connections diagram and per

Section 3 – Installing the Control 3-13 Wiring Burglary and Panic Devices to Zones 1-8 The maximum zone resistance is 100 ohms for zones 1, 2 and 8,

VISTA-32FB Installation and Setup Guide 3-14 ZONE 12-WIRE SMOKEDETECTORSMOKE2000 OHMSEOLR15162_wiresmk-001-V0 Figure 3-12: 2-Wire Smoke Detector on

Section 3 – Installing the Control 3-15 +--+-+•EOLPOWERSUPERVISIONRELAYMODULEEOLR-14-WIRE SMOKEDETECTORS2000OHMEOLRHEATDETECTOR+–BLK+-CONTROL PANELZON

VISTA-32FB Installation and Setup Guide 3-16 GLASSBREAKDETECTORZONE 8 (+)(-)LATCHING TYPE GLASSBREAK DETECTOR LOOP2000OHMSEOLR 2726glass_conn-001-V0

Section 3 – Installing the Control 3-17 Model Number Type 998MX Serialized PIR Quest 2260SN Serialized PIR IS2500SN V-Plex PIR Vplex-VSI V-plex Sho

Table of Contents iv SECTION 6: Scheduling Options...6-1

VISTA-32FB Installation and Setup Guide 3-18 Using the 4297 Polling Loop Extender The 4297 Polling Loop Extender may be used to provide additional p

Section 3 – Installing the Control 3-19 Wireless Zone Expansion The following table lists the receivers that may be used and the number of zones they

VISTA-32FB Installation and Setup Guide 3-20 Take note of the address you select for the RF receiver, as this address must be enabled in the system

Section 3 – Installing the Control 3-21 5800 Series Transmitter Setup • Transmitters have built-in serial numbers that must be enrolled in the syste

VISTA-32FB Installation and Setup Guide 3-22 UL • Relays should not re-energize until the panel is fully reset. • For Commercial Fire ins

Section 3 – Installing the Control 3-23 Installing 4101SN Relay Modules The 4101SN V-Plex Single Output Relay Module is a serial number polling loop o

VISTA-32FB Installation and Setup Guide 3-24 Wiring for the Remote Keyswitch To install the Honeywell 4146 keyswitch, perform the following steps: S

Section 3 – Installing the Control 3-25 Operation The VISTA-32FB features Dynamic Signaling Delay and Dynamic Signaling Priority message reporting whe

VISTA-32FB Installation and Setup Guide 3-26 Trouble Messages The following messages are displayed on the 6160/6160CR-2 when a problem exists on the

Section 3 – Installing the Control 3-27 Use the following instructions for wiring the 18VAC secondary winding of the internal transformer. To connect

v UL365 Police Station Connected Burglar Alarm... A-2 UL16

VISTA-32FB Installation and Setup Guide 3-28 1. In Worksheet 1, enter devices used on the polling loop. Calculate total current draw on the pollin

Section 3 – Installing the Control 3-29 3. In Worksheet 3, enter devices used on Auxiliary Power 2. Calculate standby and alarm currents, then add t

VISTA-32FB Installation and Setup Guide 3-30 5. In Worksheet 5, enter devices connected to the Bell 2 Output. Calculate alarm currents, then add t

Section 3 – Installing the Control 3-31 The total control standby load must be limited to 1A for 24-hour standby time using a 12V, 34.4AH battery con

VISTA-32FB Installation and Setup Guide 3-32 9. Connect the battery, referring to Figure 3-25. The standby battery is automatically tested for 10

4-1 SECTION 4 Programming ••••••••••••••••••••••••••••••••••••••••••••••••• Program Modes There are two programming modes for the VISTA-32FB. These

VISTA-32FB Installation and Setup Guide 4-2 Programming System-Wide Data Fields Values for some programming fields are system-wide (global), and som

Section 4 – Programming 4-3 Below are the main menu selections. For details refer to the VISTA-32FB Programming Guide. MAIN MENU OPTIONS ZONE PROG?

VISTA-32FB Installation and Setup Guide 4-4 Following is a list of commands used while in the Menu Mode: #93 Menu Mode Programming Commands #93 Ente

Section 4 – Programming 4-5 Communication Defaults *45 PRIMARY FORMAT [1] ADEMCO Contact ID *46 LOW SPEED FORMAT (Prim) [0] ADEMCO Low Speed *47

vi List of Figures ••••••••••••••••••••••••••••••••••••••••••••••••• FIGURE 1-1: ISOLATING FIRE DEVICES FROM BURGLARY DEVICES...

VISTA-32FB Installation and Setup Guide 4-6 Type 01: Entry/Exit #1 Burglary Provides entry delay whenever the zone is faulted and the system is arme

Section 4 – Programming 4-7 Type 17: Fire Waterflow Provides a trouble condition on open circuit and an alarm on a short circuit that remains longer t

VISTA-32FB Installation and Setup Guide 4-8 Using the a Relay to Unlock A Door This control can be programmed so that a user can trigger a relay fo

5-1 SECTION 5 Data Field Descriptions ••••••••••••••••••••••••••••••••••••••••••••••••• About Data Field Programming The following pages list this c

VISTA-32FB Installation and Setup Guide 5-2 FIELD TITLE and DATA ENTRIES EXPLANATION 0✴✴✴✴130 Bell 1 Timeout Enter 01-15 multiplied by 2 minutes.

Section 5 – Data Field Descriptions 5-3 FIELD TITLE and DATA ENTRIES EXPLANATION 0✴✴✴✴270 Test Report Interval Enter 001-999 for the test report in

VISTA-32FB Installation and Setup Guide 5-4 FIELD TITLE and DATA ENTRIES EXPLANATION 0✴✴✴✴370 Download Command Enables 0 = disable 1 = enable Enab

Section 5 – Data Field Descriptions 5-5 FIELD TITLE and DATA ENTRIES EXPLANATION 0✴✴✴✴480 Low Speed Format (Secondary) 0 = ADEMCO Low Speed 1 = Ses

VISTA-32FB Installation and Setup Guide 5-6 FIELD TITLE and DATA ENTRIES EXPLANATION 0✴✴✴✴640 Alpha Numeric Pager Installed Not Used. Must be set

Section 5 – Data Field Descriptions 5-7 FIELD TITLE and DATA ENTRIES EXPLANATION 0✴✴✴✴800 Zone Type Restores for Zone Types 9, 10 & 14 0 = dis

vii Conventions Used in This Manual ••••••••••••••••••••••••••••••••••••••••••••••••• Before you begin using this manual, it is important that you u

VISTA-32FB Installation and Setup Guide 5-8 FIELD TITLE and DATA ENTRIES EXPLANATION 1✴✴✴✴180 Affects Lobby (partition-specific) 0 = disable 1 =

Section 5 – Data Field Descriptions 5-9 FIELD TITLE and DATA ENTRIES EXPLANATION 1✴✴✴✴220 Cross Zoning Pair One Enter 001-032 Enter 000,000 to dis

VISTA-32FB Installation and Setup Guide 5-10 FIELD TITLE and DATA ENTRIES EXPLANATION 1✴✴✴✴350 Access Control Dialer Enables 0 = disable 1 = enab

Section 5 – Data Field Descriptions 5-11 FIELD TITLE and DATA ENTRIES EXPLANATION 1✴✴✴✴560 AC 60Hz or 50Hz 0 = 60Hz 1 = 50Hz Select the frequency f

VISTA-32FB Installation and Setup Guide 5-12 FIELD TITLE and DATA ENTRIES EXPLANATION 2✴✴✴✴020 Daylight Saving Time Start/End Weekend 0 = disable

Section 5 – Data Field Descriptions 5-13 FIELD TITLE and DATA ENTRIES EXPLANATION 2✴✴✴✴210 Supervision Pulses for Communicators 0 = disable 1 = ena

VISTA-32FB Installation and Setup Guide 5-14 FIELD TITLE and DATA ENTRIES EXPLANATION 3✴✴✴✴140 Waterflow Alarm Silence Option 0 = silenced by User

Section 5 – Data Field Descriptions 5-15 FIELD TITLE and DATA ENTRIES EXPLANATION 3✴✴✴✴310 Backup Dialer TouchTone or Rotary 0 = rotary 1 = touchto

VISTA-32FB Installation and Setup Guide 5-16

6-1 SECTION 6 Scheduling Options ••••••••••••••••••••••••••••••••••••••••••••••••• UL • You must program Bypass and Auto-Arm Fail reports for UL i

VISTA-32FB Installation and Setup Guide viii

VISTA-32FB Installation and Setup Guide 6-2 This option is set in partition-specific field 2*10. If field 2*10 is set, we highly recommend setting f

Section 6 – Scheduling Options 6-3 Using the #80 Menu Mode, the installer can program open/close schedules by assigning a time window to a day of the

VISTA-32FB Installation and Setup Guide 6-4 Example of Open/Close Exception Reporting & Scheduling The following chart gives an example of how t

Section 6 – Scheduling Options 6-5 Steps to Program Scheduling Options This section contains examples of the worksheets only. For complete workshee

VISTA-32FB Installation and Setup Guide 6-6 Time Windows he system provides 20 time windows that are defined with start and stop times. These wind

Section 6 – Scheduling Options 6-7 Part Mon Tues Wed Thur Fri Sat Sun Hol Op Cl Op Cl Op Cl Op Cl Op Cl Op Cl Op Cl Op Cl 1 2

VISTA-32FB Installation and Setup Guide 6-8 Holiday Schedule Programming After entering Scheduling Menu Mode, press [0] until the “Holidays ?” promp

Section 6 – Scheduling Options 6-9 Relay Commands Action Code Action Action Specifier 01 Relay On Relay # 02 Relay Off Relay # 03 Relay Clos

VISTA-32FB Installation and Setup Guide 6-10 Time-Driven Event Programming The following menu items must first be programmed in Output Programming i

Section 6 – Scheduling Options 6-11 ACTION CODES EXPLANATION ACTION SPECIFIER 50=Off-Normal Reminder Action 50 No action specifier is required for

ix UL864 (Commercial Fire) Compliance •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

VISTA-32FB Installation and Setup Guide 6-12 PROMPT EXPLANATION MON A1 Window 1? 00:00 00:00 00 Enter the first time-window number (01-20) for

Section 6 – Scheduling Options 6-13 Temporary Schedules Programming Enter User Code + [#] + 81 to enter this mode. PROMPT EXPLANATION Mon DISARM

VISTA-32FB Installation and Setup Guide 6-14 Entering 00 as the output number deletes the timer (Timer 06, in this example) and displays an output

7-1 SECTION 7 Downloading Primer (Remote Downloading is not a UL Listed feature) ••••••••••••••••••••••••••••••••••••••••••••••••• General Informati

VISTA-32FB Installation and Setup Guide 7-2 Getting On-Line with a Control Panel At the protected premises, the control panel must be connected to t

Section 7 - Downloading Primer 7-3 Direct-Wire Downloading The VISTA-32FB can be downloaded without using a modem or telephone line by using a 4100SM

VISTA-32FB Installation and Setup Guide 7-4

8-1 SECTION 8 Setting the Real-Time Clock ••••••••••••••••••••••••••••••••••••••••••••••••• General Information This system provides a real-time clo

VISTA-32FB Installation and Setup Guide 8-2

9-1 SECTION 9 User Access Codes ••••••••••••••••••••••••••••••••••••••••••••••••• General Information The VISTA-32FB system allows a total of 75 sec