ADEMCO Alpha Vista Console Manual de usuario descargar pdf (Pagina 52)

–52-

Addlng Custom Words

Up to 20 installerdefined words mn be added to the built-in vocabula~. Each of the 20

‘words- can sdually mnsist of seversl words, bti bear in mind that a maimum of 10

charatiers =n be used for

esch word string.

1. Seld CUSTOM

WORD mode. The keys pefiom the following fundions:

[3] Advanms through alphabet in a=enting order.

[1] Advanws through alphabet

in dewending order.

[6] Selds desired lette~ moves the cursor 1 space right.

[4] Moves the cursor one space to the left.

[7]

Insetts a space at the cursor location, erasing any charader d that location.

[8] Saves the new word in the system’s mamo~.

[.1 Returns to description entv mode.

10,

11.

Key the number of the cutiom word or word string to h creatd (01-2o). For example,

f you are creating the first word (or word stting), enter 01; when creating the semnd

word, enter 02, and so on. A cursor will now appear at the beginning of the second

line.

Use the [3] kay to advance through the alphabet (numbers, symbols and special

chara~ers ara includd). Use tha [1] key to move back through tha alphabt.

IMPORTANT Custom words must begin whh m alphabetic charader. If numbers or

symkls are used as the first charatier,

the word will not be saved.

When you have reached the desired character, press the [6] key to seled it. The

cursor will then move to the right, in psition for the next charader.

Repeat steps 5 and 6 to create the desirsd word (or words). Note that the [4] key mn

be used to move the cursor to the left h necessa~, and that key ~ can be used to

enter a blank (or to eraae an existing character). Each word or word string cafinot

ex~ed 10 charatiers.

Pre= the [8] key to save the custom word(s) and return to tha’ ED ?? display. The

custom word (or string of words) will be automatidly added w the buik-in vombulay

at the end of the group of wrds beginning wtih the same letter.

Repeat steps 4 through 8 to create up to 19 addhional custom words (or word sttings).

Pre- the ~] key to return to the .ZN ?? display, and follow the zone description enty

pmcadure to assign the new words to a zone description.

Kev 00 to ext the zone dosctiption programmiw mode.

Creating A Custom Message Display (Installer’s Message) \

Normally,

when tha system is in the disarmed state, the folbwing display is prasent on the

tinsoli.

...’DISARMEW.’ READY TO ARM

Pan or all of the ahve message can be modified to create a custom installer massage.

For example. .’”’DISARMED”” on the first line or READY TO ARM on the samn.c fine

muld be replaced by the installation ampany nama or phone number for sewice. Note

that there are only 16 charadar spaces on each of the WO lines. To craate a custom

display message, proceed as follows:

Sele@ defauk screan mode. Enter 1.

The following will appear

‘“.. DISARMED””.

RMY TO ARM

A cursor will be present at the etireme left of the first fine (over the first “star). The

[6] key is used to move the cursor to the right and the [4] key to move the cursor to

the left. Key [~ may be used to insefl spaces or erase existing charaaers.

For example, to replace READY TO ARM with the message SERVICE:424-01 77,

pro~ed as follows:

Press the [6] key to mova the cursor to the right, and wntinue until the cursor is

psnioned over the nrSt 10CaflOnon the sewnd line.

Press the [3] key to advance through tha alphabet to the first dasired character On

this case, “S”). Use the [t] key to go bactiard, when nacessa~. Whan the desirad

charatier is reached, press [6]. The cursor will then move to the nati Wsition, ready

for ent~ of the next character On this axample, “E”). When the cursor reaches a

~sition over an existing charader, prassing the [3] or [1] key will advance or back up

from that character in the alphabet. Proceed in this manner until all charaders in the

message have been entered.

To store this new display message in memo~, press the [6] key.

Press the ~] key to return to the “ ZN ?? display. To confirm that the new messagk—.

has been stored in memov, press 00 and then press 00 again. The new message

should be displayed.

Key O to exit the desctiptorfprogramming retie.

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 73 74

Comentarios a estos manuales

Sin comentarios

ADEMCO Alpha Vista Console Manual de usuario Pagina 52

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Alpha Vista Console