ADEMCO Alpha Vista Console Manual de usuario descargar pdf (Pagina 24)

E~NT LOGGING The 5140XM allows its event log to be printed on a local serial printer. If used,

PRINTER

program field 3*1 9 must be set to”1”. NOTE: This setting overrides the functions

CONNECTIONS

selected for INPUT 1 and OUT 2 made in field 3’20. Connect a UL EDP Listed

serial printer to the J2 mnnector using an Ademco 4100SM Intedacs modui~ ~s

shown below. Refer to the EVENT LOGGING PROCEDURES section O-,S

manual for a description of the console commands which initiate event log

printing,

NOTE 1: Printer must be configured as follows:

.8 data bfis, no pa~y, 1 stop bi

.300 or 1200 baud (1200 preferred)

. Har*are handshaking using DTR signal

NOTE 2: The4100SM module is supphed wih a 10 foot RS232 cable. A longer

cable or an efiension cable can be used f the 5140XM and serial printer are

separated by more than 10 feet, but the total cable length should be less than 50

feet.

NOTE 3: Most printers either ignore the CTS, DSR and CD signals, or require

them to be high ~.e. 3-15VDC as measured on RS232 DB25 connector pins 5, 8

& 8 respedtvely wtih respect to grouti pin 7). The 41 OOSM module sets these

pins Mgh. If the printer being used will not operate with these pins high, then” ctip

the blue (CTS), whfie’ (DSR) or red (CD) jumpers on the 4100SM module to set

the corresponding signal fbating. Important pins on the RS232C cable are pin 3

(data out), pin 7 (gmuti) ati pin 20 (DTR - ready).

NOTE 4: The DTR signal, as measured at 41 OOSM TB1, should be high (9.5-

14VDC) when the printer is powered, properly connected, on-line and ready to

print, This signal will be low (O-1 .5VDC) when the printer is not powered, not

properly mnnecfed, oft-fine or out of paper. The 5140XM will not send printing

data to the printer unless the DTR signal is high.

NOTE 5: If earth grou~ fauk sensing is enabled:

You may get an earth ground fault indcation when the 41 OOSM N ‘e

is clipped directly onto a sidewall of the 5140XM cabinet. If this o*,

use an insulator to insulate the 4100SM’S clip-on bracket from the

5140XM cabinet side wall. Later production versions of the 4100SM

have the chp~n bracket isolated from the circuit ground (terminal 7) and

will not have this problem.

You may alw get an earth ground fault indication if you use a printer (or

PC) which has a 3-prorrg, grounded pwer cord. [f this occurs, first verify

that pin 1 (chassis ground) is isolated from pin 7 (signal ground) on the

4100SM’S RS232 @nnector (early production versions of the 4100SM

have an unma~ed, 3/8 long, bare wire jumper lying near the pin 1 stie

of the RS232 connector which must be cut to isolate these pins). Then

verify that these pins are isolated on your prirrtefs RS232 connector.

Follow the instructions provided wfih your printer to isolate these pins if

required.

Figure 13. ~E~ LOGGING PRINmR CONNECTIONS

,, .*, x, ,.,, s.,,,. .,.

–24-

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 73 74

Comentarios a estos manuales

Sin comentarios

ADEMCO Alpha Vista Console Manual de usuario Pagina 24

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Alpha Vista Console