ADEMCO Alpha Vista Console Manual de usuario descargar pdf (Pagina 33)

V. SYSTEM OPERATION

,.-

GENERAL

INFORMATION

IINSTALLERS CODE

(lISER #1/Authorl@

Level O)

SECURIW ACCESS CODES

The 5140XM system allows up to 99 4-digit security access codes to be

programmed. When programmed, each code is assigned a user ID number and

an authority level, which determines the system functions that code can be used

to perform. There are seven authotity levels as fisted in the table below. Aside

from the installer, who programs codes at installation time, the system allows

master and manager level users to program codes on an as needed basis. These

codes are intended for use by those who need limited and/or temporary control

over system operation.

A Quick Arm feature can also be programmed (field ’29) which enables the [#] key

to be pressed instead of entering the security code when arming the burglaV

system. The security code must still be entered when disarming the system. Note

that open/close reporting of Quick Arm is enabled if User 2 is enabled for

open/close reporting, and that Quick Arm repons as user O.

TABLE OF AUTHORITY LEVELS

kvan Itle Enter Armml=rm

S!lmm

dlCh

ang B Act!vate

Pro ram

tMO e

e %urlfy ZO~e~

TestModes

:;f:~ ::PT2

ties

Trouble

O-lnsmlbr yes

Yp, m

d]sam only if L?;?ay E$%~

~g;;:alk

u=d b m

ititing fue zones

if tests,tiredill

installerlevel maw)

1-tister

yes yes yes,levels2-

ye~,b“~

6Wly

y=,

buq.

zow (md

walk tes!, tire

fire zones if

dtill only

maH&)

2-Maager

yes

~;;yls %

y=, burg b

zmes Mb

Uali t$s?

3a per~w A

yes

yes, burgla~

zones mly

4ap eratw B

Ves m

~peramr G m y;, m

dtsam only

yes

m m

u=d to am

%-Duress

yes, sen&

yes

m m

s]lent Wnic

Epon

As shipped from the factory, the installer’s code is pre-programmed to 5-1-4-0

and can be changed by the installer to any desired code (field .00).

The installer’s code is intended to be known and used only by the installer and his

aPPointed se~ice representatives. Durin9 intial installation, the installer uses this

code to program security codes for master, manager and lower level users who

will operate the system on a day to day basis (see procedures following). The

installer’s code is the only code that permits entry into programming mode, where

the system’s operating parameters can be changed. The installer’s code is also

the only code which permits fire system walk test ati!vafion and can be enabled to

permit fire sensor and system zones to be bypassed (field 3.85), The installer’s

code can be used to perform all normal system functions except that, for added

security, this code can be used to disarm the burgla~ system only if it was used to

arm the system. Note that open/close reporting for the installer is enabled in field

.39.

The system also provides an [nstaller Code lock-out feature, which prevents the

use of the Installer’s Code from re-accessing the Programming mode after the

initial programming. This feature is activated by pressing ’98 to exit Programming

mode. The only way to access Programming mode once this feature is activated,

is by powering down the system and powering up again, and then pressing both

Ihe ‘ and # keys at the same time wifhin 30 seconds of power up. If re-access to

Programming mode using the Installer’s Code is desired after initial programming,

then exit Programming mode by pressing “99.

-33-

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 73 74

Comentarios a estos manuales

Sin comentarios

ADEMCO Alpha Vista Console Manual de usuario Pagina 33

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Alpha Vista Console