ADEMCO Alpha Vista Console Manual de usuario descargar pdf (Pagina 47)

GENERAL

INFORMATION

IGOMMUNICATION

DEFAULTS

To help expedite the installation, Ademco has incorporated 4 different

communication defauffs in the Control (Low Speed, Ademco Express, Ademco

High Speed &Ademco’s new Contacted). These defaults automatically program

indust~-standard code assignments for zones, keypad panics, non-alarm and

supervisory conditions, and can be loaded at any time without affecting non-

communication program fields. Using these defaults saves programming time!

After loading one of the communication defaults, you only need to wire the

devices to their appropriate zones, and program the following:

. Central station phone number(s), fields”33 & ’34

. Subscnbe~s aaunf number(s), fields’32 &*90

. Zonety~ responses, fields ‘02-’05, 1’01-1’05 & 710

.Belll, Be112and Aux Relay assignments, fields Y15, V61,3’70-3’81.

. Delay s, timeouts, ati miscellaneous ~ntrol options.

The system is then operational.

NOTE: Defauff communication wmmands are in second set of programming

fields (fields 1’80, 1’81, 1“82 & 1“83).

Once the Programming mode is entered, clear tha system’s memory by pressing

“97. TMsensures allprogram tieldsare settotheir factoVset, pre-programmd

values. If desired, foadone of thecommunication defauff programming sets by

first changing to the 1’XX set of fields (press ‘94), then entering one of the

following field numbers:

The program fields that are affected by loading one of the communication

defaufts are fields’45 -’82, 1’40,1.41740-3’42, 3’50-752. Defauk values for

each communication default are listed at the end of this manual. For detailed

information about reporting formats, see the SYSTEM COMMUNICATION

section. Affer loading one of the defauff sets, proceed to program the system

data fields as described in the PROGRAMMING DATA FIELDS section.

EA,SY-TO-PROGRAM

COMMUNICATION

FIELDS

The programming scheme eliminates the need to program zones to channels,

and then channels to codes. If programming communication fields manually,

simply enter whatever code (3+1, 4+1, 4+2 or Ademco Express) is to be sent for

each zone (including panics, non-alarm males and supervisory codes). NOTE:

Enter”1 O to transmit an “W, which appears as “O at the receiver.

All zones are separated into groups of 8, with common rastore, trouble and

bypass codes for evey 2 groups (16 zones). There are 2 double-digit entries for

each code. For 3+1, 4+1, 4+2 and Ademo Express, the first entry is the alarm

code for a standard reporf. The second entry is the ID digit for an expanded 3+1

or 4+1 re~rt, or for a 4+2 or Ademco Express report. If the second digit is O,

only 3+1 or 4+1 (or 4+1 express) non-expanded messages will be sent. If only

three digits are entered in the account number field, the ID or second dgits are

ignored, if entered. For Ademco Mgh Speed format, the first digit entry is the

channel assignment for that zone, and the second digit is ignored, if entered.

For Contact ID reporting, the first digit entry (any non zero entry) enables

reWrting for that zone, and the second digit is ignored.

NOTE: Restoral reports for an event will not be sent if the event ifse!f is not

enabled, even if a restore code is programmed for that event.

—47—

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 73 74

Comentarios a estos manuales

Sin comentarios

ADEMCO Alpha Vista Console Manual de usuario Pagina 47

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Alpha Vista Console