ADEMCO Alpha Vista Console Manual de usuario descargar pdf (Pagina 50)

#93 USER FRIENDLY MENU MODE

GENEW INFORMATION After programming all system related programming fieUs in the uwal way, pres

W3 to display the first choice of the three menu driven programming funtions,

which are: Zone Programming (for programing zone types), Alpha PmgramfiW _

(for prqramming alpha descriptors) & Device Programming (for programming

console characteristics). Press O (NO) or 1 (YES) in res~nse to the selection.

Pressing O will display the next choice in sequence. Refer to the ZONE

PROGRAMMING section for instrutilons for programming zone characteristics,

the DEVICE PROGRAMMING section for instructions for programming remote

consoles, and the ALPHA PROGRAMMING section for programming alpha

descriptors. The hst of commands used while in the menu mode is shown at the

right.

zoNE PROGmMMING

The following fields can be programmed by using the ZONE PROGRAMMING

Menu Mode:

ZONE PROGRAMMING FIELDS

‘02-’05

Zone response types for zones 1-27, 95-99

1’01-1.05

Zone response tvpes for zones 28-M

3’10

Zone reswnse typ

es for system zones 70-75

Enter Programming mode, then press *3 to display “ZONE PROG?”. Press

1 to enter ZONE PROGRAMMING rode,

Enter the zone number to be pr~rammed (01-~, 70-75, 95, 96,97 or 99).

Press p] to accept entry,

Enter the zone response type for that zone (01 -19). The screen will

automatically dsplay the zone type for the number entered. Press p] to

accept ent~. If a different zone res~nse type is desired, enter a different

number and press ~].

The display will repeat with the zone number question for programming the

other zones in the system. Enter 00 to exit back to normal programming

mode.

W3 MENU MODE KEY COMMANDS

Enters Menu mode

[*] Sewes as ENTER key, Press to have console accept entry.

[#]

Skips to next screen displav

without changing existing entries,

Press to answer NO

Press to answer YES

0149

All entries are 2digit entries

Ewapes

from menu mode. back into field programming mode

DWICE

PROGRAMMING

NOTE 1: Console 10 number 00 is permanently enabled and set for no sounder

suppression. TMs cannot be changed.

NOTE 2: The panel is factory pre-programmed with all console ID numbers (01-

30) enabled and set for no sounder suppression. Use the DEVICE

PROGRAMMING mde ‘at initial installation only if it is desired to change

the sounder options for one or more

mnsoles

Enter Programming mode, then press H3 to display “ZONE PROG?”. Press

O (NO) to display “ALPHA PROG?”. Press O again to display “DEVICE

PROG?. Press 1 to enter OEVICE PROGRAMMING mode.

2. Enter the 2-digit console ID number as set by its DIP switches (01-30). Press

p] to accept entry.

Enter 01 and press ~]. Enter 01 again and press ~].

Enter a number 00-03 for the console soundhrg suppression options desired

for this console as follows:

Enter 00 for no suppression.

Enter 01 to suppress artidisann & entry/exit beeps.

Enter 02 to suppress chime mode beeps only.

Enter 03 to suppress ar~disarm, entry/exit and chime ~de beeps,

The screen will display the next console number to be programmed.

press 00 to exit Menu Mode.

–50–

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 73 74

Comentarios a estos manuales

Sin comentarios

ADEMCO Alpha Vista Console Manual de usuario Pagina 50

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Alpha Vista Console