ADEMCO Alpha Vista Console Manual de usuario descargar pdf (Pagina 17)

AUXILIARY RELAY

The 5140XM provides a built-in “Form C“ relay with contacts rated at 28

VACNDC, 2.8 amps max. This relay maybe programmed for one of the funcfbns

betow (field 3’61):

. Alarm Activation: Steady acfivatin in response to an alarm on one, some

or all zones as selected in fie~s 3’70 through 3’81. If field 361 is set to”1”,

the auxiliay relay remains asfivated until timeout (which is programmed

independent of the bell 1 and bell 2 timeouts; tieti 3’60) or until the 5eCurify

code + OFF has been entered. If field 3’61 is set to ‘4, the auxihary relay

remains activated until the installer or master mde + [#] +67 is entered.

When this functiin is used, the auxiha~ relay Hn be used for elevator recall or

ventilator shutdown on fire alarms or when wired to the aux power 1 output or

to a separate power supply (such as Alarm-Saf model AS/PS5-BFS-l 2-UL

see the REMOTE CONSOLES section), the auxiliary relay can be used to

provide a third (unsupewised) bell output for supplementa~ strobes,

sounders, etc. as irrdiiatad in the diagram, below. By defauk, the auxilia~f relay

is sef to acfiiafe on zone 1-8 alarms with no timeout (field 3“61 =1 ) as m“~hf W

required for a common fire and burglaV alarm strobe itilmtor usage.

When fieM 3’61=1, the auxiliary relay can also be programmed to give a brief

ativafion for confirmation of arming (field 757) or for errfry/exit or perimeter

zone fauks while CHIME me is active (fieti 759).

. Trouble/Supervisory Activation: Steady activation in response to any

zone or system related trouble co~tion or to any fire supervisory condiiin.

Remains activated until all fault conditions have been corrected and the

security de + OFF has been entered.

. 4-Wire Smoke Detector Reset: Momentary (6 second) activation at

second entry of OFF sequence wtich interrupts power to 4-wire smoke

detectors connected to hard-wired zones (zones 1-8) or to polfing tip zones,

allowing the detectors to be reset following an alarm. Power to 4-wire smoke

detectors should be wired to the auxitia~ relay and to the auxilia~ power 1

output as shown in the diagram bebw.

. Batte~ Savefi When ttis function is selected, the auxiha~ relay will normally

be activated ~.e. N.O. and pole contacts will be connected, N.C. confa~ will be

open) and will de-advate 4 hours after the stafi of an AC power failure. Using

this feature, noncritical toads (such as supplementary mnsoles) which do no

need to be supported for the full 24 hour baffeV backup period can be

disconnected from the auxitiary outputs, allowing a smaller capacity battery to

be used. The relay re-acfivates within a few seconds after AC power restores.

Rgure 5a. AUXILIARY REMY WIRING

(Shows how to wire A.. Relay for .nsupewisd, poweti

slam output.)

- ALARM

r/7

78910

11et2

AUX REMY

)

FACTORY DEFAULTS

. Activates for zones 1-8

~ : : :

alms (steady alm

: x

output)

;

. No t,meo”t

NOTES

/“ ;

. u.. no.-polatiz~

cAN DWW pOWERFROMWE AUX WR 1

i“ticati”g devices

OUTPUTORFROMSEPAWTE SUPPLY

. wring is not

..pemised

. Do not exceed !he

raflngs of the SUPPIY

u=O. 17au. pwr 1

output used, then

c.mtined slam

c.ment drawn from

,“. pwr 1, a.x pwr 2,

bell 7 and bell 2

.a..ot ,xce&

2.3A mm.

figure 5b. AUXIL1~Y REWY WIRING

(Show how to ware.“, relay for 4-wire moke deltior wwer 1=.1)

EOLR

.- 17 –

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 73 74

Comentarios a estos manuales

Sin comentarios

ADEMCO Alpha Vista Console Manual de usuario Pagina 17

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Alpha Vista Console