ADEMCO Vista-128B PLUS Especificaciones descargar pdf (Pagina 64)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

5-4

FIELD

TITLE and DATA ENTRIES EXPLANATION

*32

Primary Subscriber’s Account

Number (partition-specific)

Enter

00-09; B-F (11-15)

Enter a 3- or 4-digit (depending on report format) primary subscriber

account number. Each number requires a 2-digit entry so as to allow

entry of hexadecimal digits (B-F). If a 3-digit account number is to be

used, enter data only in the first 3 locations, and enter * in the fourth

location.

*33

Primary Phone Number

Enter

0-9; #11

for *

, #12

for

#, #13

for

a 2-

second pause.

Enter the primary central station phone number, up to 17 digits. This is

the phone number the control will use to transmit Alarm and status

messages to the central station. Do not fill unused spaces.

NOTE:

Backup reporting is automatic only if a secondary phone number

is entered.

*34

Secondary Phone Number

Enter

0-9; #11

for *

, #12

for

#, #13

for

a 2-

second pause.

Enter the secondary phone number, up to 17 digits. The secondary phone

number

is used if communication on the primary number is unsuccessful,

or if split/dual reporting is desired. Do not fill unused spaces.

NOTE:

If this field is programmed, a secondary subscriber account

number (field *90)

must

also be programmed.

*35

Download Phone Number

Enter

0-9; #11

for *

, #12

for

#, #13

for

a 2-

second pause.

Enter the downloading phone number, up to 17 digits. Do not fill unused

spaces.

NOTE:

This field is applicable only if downloading is utilized.

*36

Download ID Number

Make entries as 2-digit numbers as follows:

00=0 01=1 02=2 03=3 04=4 05=5

06=6 07=7 08=8 09=9 10=A 11=B

12=C 13=D 14=E 15=F

Enter eight digits.

NOTE:

This field is applicable only if downloading is utilized.

*37

Download Command Enables

= disable

= enable

Enabling a function means that you are able to perform that function via

the ADEMCO Compass Downloading software.

Functions are as follows: Dialer Shutdown; System Shutdown; Not Used;

Remote Bypass; Remote Disarm; Remote Arm; Upload Program;

Download Program.

For UL installations, all entries must be

*38

Prevent Zone XXX Bypass

(partition-specific)

Enter a zone number

(001-250)

Enter

000

if all zones can be bypassed.

Enter three digits for zone that cannot be bypassed by the user.

NOTES:

The actions manual bypass, group bypass, auto-stay, and STAY/INSTANT

arming modes cannot bypass any zone programmed in this field.

The system will not arm if the zone is programmed with the vent zone or

force arm fault attributes.

*39

Enable Open/Close Report for

Installer Code (partition-specific)

= disable

= enable

If enabled, whenever the Installer Code is used to arm or disarm the

partition, an open/close report is sent to the central station.

*40

Enable Open/Close report for

Keyswitch

= disable

= enable

If enabled, whenever the keyswitch is used to arm or disarm the partition,

an open/close report is sent to the central station.

*41

Normally Closed or EOLR (Zones

2-8)

= disable

= enable

If disabled, end-of-line resistors must be used on zones 2-8.

If enabled end-of-line resistors cannot be used and only

normally closed

devices must be used.

Must be

for UL installations.

1 2 ... 59 60 61 62 63 64 65 66 67 68 69 ... 127 128

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-128B PLUS Especificaciones Pagina 64

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS