ADEMCO Vista-128B PLUS Especificaciones descargar pdf (Pagina 35)

Section 3 - Installing the Control

3-17

Smoke Detector Reset

Output 1 may be used to reset 4-wire smoke detectors.

Use this output to trigger a low current relay, and wire

the power for the smoke detectors through the relay’s

contacts.

NOTE:

The output is normally high (12VDC) and goes

low when the User Code + Off is entered at the keypad.

To install a relay for smoke detector reset, perform the

following steps:

Step Action

1 Connect power terminals of the relay to the

panel’s auxiliary power (terminals 6 & 7).

2 Connect trigger input of the relay to Output 1

on J7.

3 Connect the “pole” (common) of the relay to

terminal 6 of the control.

4 Connect the positive side of the smoke

detectors to the normally closed contact of the

relay.

5 Connect the negative side of the smoke

detectors to terminal 7 of the control.

Remote Keypad Sounder

This feature is available in the VISTA-128BP only.

An optional Amseco PAL 328N Piezo Sounder can be

used to duplicate the sounds produced by the keypad's

built-in sounder. The panel will remote all sounds (e.g.,

alarm, trouble, chime, entry/exit, etc.) produced by the

keypad's built-in sounder except for the short beeps

associated with keypad key depression. One

application of this feature might be to produce chime

sounds at a distant location from the panel's keypads.

Remote Keypad Sounder Setup

To setup for a remote keypad sounder, connect the

piezo sounder to the panel’s positive auxiliary power

output and to Output 1 on the J7 connector as shown in

Figure 3-26

Program field 1

✳

46 Auxiliary Output Enable with a [

1 2 3 4 5 6 7 8 9

GRAY (GROUND)

YELLOW (OUT 1)

WHITE (GROUND)

RED (OUT 2)

GREEN (GROUND)

BROWN (OUT 3)

BLUE (GROUND)

BLACK (OUT 4)

J7 CONNECTOR

IF USED.

1. OUT 1 IS NO LONGER

USABLE FOR SMOKE

DETECTOR RESET

OR GROUND START

(SEE FIELD 1*46).

2. OUT 2, 3, 4 CAN STILL BE

USED TO PROVIDE ALARM

STATUS INDICATIONS OR

TO OPERATE A KEYSWITCH

(SEE FIELD *15).

N/U

4142TR CABLE

BLACK

–

AMSECO PAL-328N

PIEZO SOUNDER

RED

TO AUX POWER +

TERMINAL 6

10mA CURRENT DRAIN)

J7_trigcon-001-V0

Figure 3-26: Remote Keypad Sounder Wiring

Installing the VA8200 Panel Link Module

The VA8200 Panel Link Module (PLM) connects to the

keypad (ECP) terminals on the VISTA-128BP/VISTA-

250BP and also connects to other PLMs via the RS-485

bus (3-wire twisted cable run).

Figure 3-27

is a block

diagram of a panel linking setup using three control

panels.

Panel Linking is not permitted in UL

installations.

CONTROL

PANEL

CONSOLE

PLM

CONTROL

PANEL

CONSOLE

PLM

CONTROL

PANEL

CONSOLE

PLM

ECP

RS-485

PLG-001-V0

Figure 3-27: Panel Linking Block Diagram

ECP Wire Run Limitations

Determine wire gauge by referring to the table below.

Wire Run Length Table

Wire Gauge

Length

#22 gauge 450 feet

#20 gauge 700 feet

#18 gauge 1100 feet

#16 gauge 1750 feet

•

The length of the ECP wire runs combined

must not exceed 2000 feet when unshielded

cable is used (1000 feet if unshielded cable is

run in conduit or if shielded cable is used).

•

If more than one ECP device is wired to a

single run, then the above maximum lengths

must be divided by the number of devices on

the run (e.g., the maximum length is 225 feet

if two keypads are wired on a #22 gauge run).

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 127 128

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-128B PLUS Especificaciones Pagina 35

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS