ADEMCO Vista-128B PLUS Especificaciones descargar pdf (Pagina 39)

Section 3 - Installing the Control

3-21

Alphanumeric

PP Date Time EA ZZZ SSSS AD

Where:

PP Partition number (e.g., P1)

Date Date the event occurred (e.g., 03/15/00)

Time Time the event occurred (e.g., 01:16AM)

EA Event alpha descriptor (see

APPENDIX D

)

ZZZ Zone or user number

SSSS The partition’s 4-digit subscriber number

(in field

✳

32)

AD The zone’s programmed alpha descriptor

✳

If the event is an arming or disarming, a 6-

character descriptor can be sent for the user, if

programmed, instead of the user number. The

descriptor can be programmed only via the

Compass Downloader.

The installer code has a default of INSTLR and

user number 002 has a default of MASTER for

the 6-character descriptor.

Mounting the Alpha Pager Module

The Alpha Pager Module (APM) may be mounted in the

control cabinet if space is available or, if this is not

possible, on the side of the cabinet or adjacent to it.

Do not mount the Alpha Pager Module on the

cabinet door or attempt to attach it to the PC

board.

To mount the Alpha Pager Module, perform the

following steps:

Step Action

1 If you are mounting the Alpha Pager

Module inside the control cabinet, attach it

to the cabinet’s interior surface with 2-faced

adhesive tape.

2 If you are mounting the Alpha Pager

Module outside the cabinet, use the bracket

interface (Ademco Part Number K5350).

Wiring the Alpha Pager Module

The Alpha Pager Module connects via the 4142TR cable

to the J8 connector on the VISTA-128BP/VISTA-250BP.

To wire the Alpha Pager Module, refer to

Figure 3-30

and perform the following steps:

Step Action

1 Connect the 4142TR to J8 on the control.

2 Connect the Brown wire of 4142TR to the

Orange wire of the APM.

3 Connect the Green wire of the APM to TB1-

23 of the control panel.

4 Connect the Red and Black wires of the APM

to terminals 6 and 7 (auxiliary power (+) and

(-), respectively) of the control.

5 Connect the APM RJ11 connector labeled

LINE to the handset terminals on the control

panel (terminals 26 and 27).

6 Connect the handset side of telephone line to

APM RJ11 connector labeled PHONE

(Optional) (Brown and Gray wires of Phone

Cord).

7 If you are using a parallel or serial printer,

connect the printer according to the

instructions accompanying the APM

•

The serial printer must be configured for a

baud rate of 1200, seven data bits, even parity,

and one stop bit. (7/E/1).

•

Automation software cannot be used if a serial

printer is used on the system.

VA8201 ALPHA PAGER MODULE

AUX

PWR.

PARALLEL

PRINTER

PARALLEL

OUTPUT

SERIAL

OUTPUT

DATA /

POWER

TO PHONE

TO LINE

EARTH

GROUND

HOME AUTOMATION COMPUTER

TIP

RING

RJ31X

JACK

TIP

RING

INCOMING TELCO LINE

ANSWERING

MACHINE

CALLER ID

UNIT

PREMISES

CALLER ID UNIT,

ANSWERING

MACHINE, AND

PHONES

RED

BROWN

GRAY

GREEN

RED

BLACK

GREEN

RED

BLACK

GREEN

AUX

GND.

62627282930237

TIP RING

HANDSET

TIP RING

INCOMING

PHONE

CORD

(ZONE 9)

BROWN WIRE

FROM 4142 TR

TRIGGER CABLE

SPLICE

VA8201-SOC-V1

1 2 3 4 5 6 7 8 9

BROWN

ORANGE

CONTROL PANEL

NOTE

WHEN USING THE VA8201, ZONE 9 CAN NO

LONGER BE USED AS A PROTECTION ZONE.

Figure 3-30: Wiring the Alpha Pager Module

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 127 128

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-128B PLUS Especificaciones Pagina 39

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS