ADEMCO Vista-128B PLUS Especificaciones descargar pdf (Pagina 41)

Section 3 - Installing the Control

3-23

WEEKLY TESTING IS REQUIRED

TO ENSURE PROPER OPERATION

OF THIS SYSTEM.

POLE Door Strike/Mag Coil

DATA 1 (WHITE)

DATA 0 (GREEN)

NOTE 1: USE UL LISTED ENERGY CABLE FOR ALL CONNECTIONS.

NOTE 2: VISTAKEY TB3 TERMINAL 5 IS A GROUND AND MAY BE

USED INSTEAD OF TB3 TERMINAL 2. TB3 TERMINALS 2 AND 5 ARE

A COMMON GROUND.

NOTE 3: WHEN USING TRIGGER TO TURN ON AN LED OR BUZZER,

RETURN HIGH SIDE OF LED OR BUZZER TO TB3 TERMINAL 7.

TRIGGER RATING IS 15mA AT 12VDC.

+5V

GND

TRIGGER (SEE NOTE 3)

+12V (RED)

ZONE C (General)

ZONE A (DSM)

ZONE B (RTE)

POLLING LOOP -

14V MAX (12V @ 85-160mA Nominal)

POLLING LOOP +

GND

N/O DOOR STRIKE POWER

N/C MAG COIL POWER

11 1223456789101

RELAY CONTACT RATINGS:

3A @ 28VDC MAX. (RESISTIVE LOAD)

TB 1

TB 3

READER INTERFACE CABLE

GND (BLACK)

RDR LED (ORANGE)

TO ALARM SYSTEM

CONTROL PANEL

POLLING LOOP TERMINALS.

CONNECTION

VISTAKEY

THIS DEVICE COMPLIES WITH PART 15 CLASS A

LIMITS OF FCC RULES. OPERATION IS SUBJECT

TO THE FOLLOWING TWO CONDITIONS:

(1) IT MAY NOT CAUSE HARMFUL INTERFERENCE.

(2) IT MUST ACCEPT ANY INTERFERENCE THAT

MAY CAUSE UNDESIRED OPERATION.

DOOR

CONTROL

RELAY

FOR ADDITIONAL RATINGS AND

SPECIFICATIONS, REFER TO

INSTALLATION INSTRUCTION

FOR THE VISTAKEY-SK.

THIS EQUIPMENT SHOULD BE INSTALLED IN

ACCORDANCE WITH THE NATIONAL FIRE

PROTECTION ASSOCIATION'S STANDARDS 70 &

74 (NATIONAL FIRE PROTECTION ASSOC.,

BATTERYMARCH PARK, QUINCY, MA. 02269).

PRINTED INFORMATION DESCRIBING PROPER

MAINTENANCE, EVACUATION PLANNING AND

REPAIR SERVICE IS TO BE PROVIDED WITH

THIS EQUIPMENT.

TO TB1, 11 OR 12

+ 12 VDC TO ONLY

ONE OF THESE INPUTS.

(FROM TB1-1)

Figure 3-31: Wiring the VistaKey

Access Control Using the PassPoint Access Control System

The VISTA-128BP/VISTA-250BP interfaces with the

PassPoint ACS via the VISTA Gateway Module (VGM).

The VGM is connected between the ECP bus (keypad

terminals) of the control and the network bus of the

PassPoint ACS.

The control sends the VGM its status information,

event log entries, and entry/exit requests (inputs

programmed with response type Access Point) from

keypads, hardwired zones, and RF transmitters.

The VGM then reformats and retransmits this

information to the Main Logic Board, (MLB) on the

PassPoint ACS network bus.

Interfacing the VISTA-128BP/VISTA-250BP with

the PassPoint Access Control System via the

VISTA Gateway Module is not permissible for

UL installations.

Wiring the VISTA Gateway Module

The VISTA Gateway Module is connected between the

ECP bus (VISTA-128BP/VISTA-250BP keypad

terminals) and the network bus of the PassPoint Access

Control System. See

Figure 3-32

for the proper wiring

connections.

}

ECHELON NETWORK

(PASSPOINT ACS)

YELLOW

RED

BLACK

PROM C

TRANSFORMER

4-PIN

KEYPAD

PLUG

}

CONTROL’S

KEYPAD

TERMINALS

GREEN

Figure 3-32: Wiring the VISTA Gateway Module

Event Log Connections

This system has the ability to record up to 1000 events

of various categories in the Event Log (history log).

Each event is recorded with the time and date of its

occurrence (if real-time clock is set). The categories are

Alarm, Supervisory/Check, Bypass, Open/Close, and

System conditions.

The log may be viewed on an alpha keypad, or printed

on a parallel or serial printer.

NOTE:

If you are using a parallel printer you must use

the VA8201 Alpha Pager Module.

Printer Configurations

Configure the serial printer as follows:

•

7 data bits, even parity, 1 stop bit

•

1200 baud

•

When using a printer, field 14 must be

programmed for RS232 input (1). Zone 9

can longer be used as a protection zone.

•

If you are using a serial printer, terminal 23

on the control panel cannot be used to

interface with Automation software

Using the Alpha Pager Module (APM)

To connect a printer using the Alpha Pager Module,

perform the following steps:

Step Action

Connect the APM to the control (see

Installing the Alpha Pager Module

previously

in this section)

Connect the printer according to the

instructions that accompany the APM.

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 127 128

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-128B PLUS Especificaciones Pagina 41

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS