ADEMCO Vista-128B PLUS Especificaciones descargar pdf (Pagina 62)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

5-2

FIELD

TITLE and DATA ENTRIES EXPLANATION

*10

Exit Delay #1 (partition-specific)

Enter

03-15

multiplied by 15 seconds.

= no delay.

Exit delay defines the delay period that allows users to leave the premises

through a door that has been programmed as an entry/exit delay door

after arming the system without setting off the alarm.

*11

Entry Delay #2 (partition-specific)

Enter

02-15

multiplied by 15 seconds.

= no delay.

Entry Delay #2 is used for a secondary door requiring a longer delay than

those assigned to Entry Delay #1.

This delay may not exceed 45 seconds for UL installations.

*12

Exit Delay #2 (partition-specific)

Enter

03-15

multiplied by 15 seconds.

= no delay.

Exit Delay #2 is used for a secondary door requiring a longer delay than

those assigned to Exit Delay #1.

This delay may not exceed 60 seconds for UL installations.

*13

Alarm Sounder Duration

(partition-specific)

Enter

01-15

multiplied by 2 minutes.

= no timeout.

Defines the length of time the Bell Output and the keypad’s sounder will

sound for all audible alarms.

Must be a minimum of 16 minutes for UL installations.

Burglary or RS232 Input

= burglary

= RS232 input

If enabled, sets terminal 23 (high side (+) of zone 9) as an RS232 input.

This enables the system to receive serial data (75 baud) via terminal 23.

Using the RS232 input for automation is not permitted in UL installations.

*14

*15

Keyswitch Assignment

Enter

1-8

partition keyswitch is being used.

Enter

if the keyswitch is not used.

The keyswitch requires the use of zone 7 wired loop (zone 7 is no longer

available as protection zone). The fire and panic alarm voltage triggers

(J7) automatically become ARMING and READY status outputs for the

Keyswitch LEDs.

Openings/closing report as user “0” if enabled in field *40.

*16

Confirmation of Arming Ding

(partition-specific)

= disable

= enable

If enabled, produces ½-second external alarm sounding (“ding”) at the end

of exit delay (or after kissoff from the central station, if sending closing

reports).

Must be 1 for UL installations.

*17

AC Loss Keypad Sounding

= disable

= enable

If enabled, sounding at the keypad (rapid beeping) occurs when AC power

is lost (sounding occurs about 2 minutes after actual AC loss).

*19

Randomize AC Loss Report

= disable

= enable

If enabled, randomizes AC loss reporting between 10 and 40 min. after an

actual AC loss.

If disabled, AC loss reporting about 2 minutes after actual AC loss.

Selecting this option helps prevent an overload of AC loss messages at the

central station during a community blackout.

*20

VIP Module Phone Code

1-9

= first digit of access code

∗

= second digit of access code (enter #

+11 for “

∗

”, or # +12 for “#”)

To disable enter

for the 1

digit

If a 4285/4286 Voice Module is being used, enter the 2-digit phone code

used to access the system.

Must be disabled for UL installations.

*21

Prevent Fire Timeout

= disable (timeout)

= enable (no timeout)

If enabled, there is no timeout of the alarm sounder duration for all fire

zones, regardless of partition, so that fire sounding continues until the

system is reset.

If disabled, (timeout) the normal burglary sounder duration (field

✳

13)

applies to fire alarms.

1 2 ... 57 58 59 60 61 62 63 64 65 66 67 ... 127 128

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-128B PLUS Especificaciones Pagina 62

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS