ADEMCO Vista-128B PLUS Especificaciones descargar pdf (Pagina 32)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

3-14

Installing Output Devices

The VISTA-128BP/VISTA-250BP support up to 96

outputs. Each device must be programmed as to how to

act (ACTION), when to activate (START), and when to

deactivate (STOP). The 4204, 4204CF, FSA-8, FSA-24,

4140SN and/or Powerline Carrier devices may be used

as output devices.

Installing the 4204 and 4204CF Relay Modules

Each 4204 module provides 4 relays with Form C

(normally open and normally closed) contacts. Each

4204CF module adds two style Y supervised bell

outputs to the system. For 4204CF modules, only

relays 1 and 3 on each module can be programmed.

The relay module will not operate until the

device address you have set the DIP switches

for is enabled in the control’s

Device

Programming

in the

#93 Menu Mode

To install the relay modules, see

Figures 3-21

and

3-22

and

perform the following steps:

Step Action

1 Set the 4204 or 4204CF’s DIP switches for a

device address

01-15

Do not use an address being used by another

device (keypads, RF receivers, etc.).

2 Mount the 4204 and 4204CF Modules per the

instructions provided with them.

Connect the module’s wire harness to the

control (6, 7, 8, and 9). Plug the connector

(other end of harness) to the module.

If you are mounting remotely, homerun each

module to the control. The table below shows

the maximum wire run lengths. Refer to the

instructions provided with the 4204CF for its

maximum permissible wire lengths.

Wire Gauge Maximum Length

#22 125 feet

#20 200 feet

#18 300 feet

#16 500 feet

SWITCH 4204 ADDRESS SETTINGS

POSITION ("—" means "OFF")

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

ON — ON — ON — ON — ON — ON — ON — ON —

ON ON ——ON ON ——ON ON ——ON ON ——

ON ON ON ON ————ON ON ON ON ————

ON ON ON ON ON ON ON ON ————————

12345

➞

13 14 15 16

OFF

➞

DIP SWITCH

FOR SETTING DEVICE ADDRESS

AND ENABLING/DISABLING TAMPER

➞➞

COVER TAMPER (REED) SWITCH

➞➞

TB1

4204

TB2

4-PIN CONSOLE PLUG

➞➞

121110987654321

▲

RELAY

TYPICAL

(SHOWN "OFF")

EITHER OR BOTH

CAN BE USED

➞➞

DATA IN

FROM CONTROL

(–) GROUND

DATA OUT

TO CONTROL

(+) 12V

YEL

BLK

GRN

RED

Figure 3-21: 4204 Relay Module

SWITCH 4204CF ADDRESS SETTINGS

POSITION ("—" means "OFF")

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

ON — ON — ON — ON — ON — ON — ON — ON —

ON ON ——ON ON ——ON ON ——ON ON ——

ON ON ON ON ————ON ON ON ON —— ——

ON ON ON ON ON ON ON ON ————————

12345

➞

OFF

➞

13 14 15 16

DIP SWITCH

FOR SETTING DEVICE

ADDRESS AND

ENABLING/DISABLING

TAMPER

➞➞

COVER TAMPER (REED) SWITCH

➞➞

TB1

TB2

4-PIN CONSOLE PLUG

➞➞

121110987654321

▲

EITHER OR BOTH

CAN BE USED

➞➞

DATA IN

FROM CONTROL

(–) GROUND

DATA OUT

TO CONTROL

YEL

BLK

GRN

RED

(+) 12V; SUPPLIES POWER TO MODULE

CIRCUITRY (INCLUDING NOTIFICATION

APPLIANCE RELAY COILS). CURRENT

DRAIN AT 12V IS: 25 mA + (80 mA PER

ACTIVE OUTPUT)

NOTIFICATION APPLIANCE AND

CONSOLE DATA OUTPUTS ARE

POWER LIMITED

–

NOTIFICATION

APPLIANCE B

2K EOLR

#610-7

POLARIZED

NOTIFICATION

APPLIANCE

–

NOTIFICATION

APPLIANCE A

2K EOLR

#610-7

}

–

POWER FOR

NOTIFICATION APPLIANCE A,

NOTIFICATION APPLIANCE B

8-28VDC OR VFW. UP TO 2.4A

DEPENDING ON BELL CURRENT

- ALARM POLARITY

SHOWN

- EACH OUTPUT

PROVIDES

STYLE Y

SUPERVISION

- EACH OUTPUT

RATED 1.2A MAX

- USE

NOTIFICATION

APPLIANCES

COMPATIBLE

WITH

NOTIFICATION

APPLIANCE

POWER SUPPLY

VOLTAGE

RATING

Figure 3-22: 4204CF Relay Module

Installing the FSA Modules

The 8-zone LED Fire System Annunciator FSA-8 and

24-zone LED Fire System Annunciator FSA-24 enable a

fire response unit to identify quickly the point/zone of a

fire. These indicators may be used for other functions

as well, such as status indication. A maximum of 4 FSA

modules, in any combination, can be supported.

The FSA module will not operate until the

device address you have set the DIP switches

for is enabled in the control’s

Device

Programming

in the

#93 Menu Mode

To install the FSA module, refer to

Figure 3-23

and

perform the following steps:

Step Action

1 Set the FSA’s DIP switches for a device

address from 08 to 23. See the module’s

instructions for the DIP switch table.

Do not use an address being used by another

device (keypads, RF receivers, etc.).

2 Mount the FSA module horizontally to a

duplex box (quad box for FSA-24).

3 Connect the module to the control’s keypad

terminals (6, 7, 8, and 9).

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 127 128

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-128B PLUS Especificaciones Pagina 32

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS