ADEMCO Vista-128B PLUS Especificaciones Pagina 53
- Pagina / 128
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Section 4 – Programming
4-3
Below is a list of the main menus. For details refer to the
VISTA-128BP/VISTA-250BP Programming Guide.
MAIN MENU
OPTIONS
ZONE PROG?
1 = YES 0 = NO 0
For programming the following:
•
Zone Number
•
Zone Response Type
•
Partition Number for Zone
•
Dialer report code for zone
•
Input Device Type for zone (whether RF, polling loop, etc.)
•
Enrolling serial numbers of 5800 Series transmitters & serial polling loop devices into the system.
•
Zone Attributes (e.g., Arm w/Fault, Silent, etc.).
EXPERT MODE?
1 = YES 0 = NO 0
Same as Zone Programming except:
•
Done with a minimum number of keystrokes.
•
Can program wireless keys using pre-defined templates.
REPORT CODE PROG?
1 = YES 0 = NO 0
For programming the following:
•
Alarm report codes for zones
•
Restore and supervisory codes
•
All other system report codes
ALPHA PROG?
1 = YES 0 = NO 0
For entering alpha descriptors for the following:
•
Zone Descriptors
•
Installer’s Message
•
Custom Words
•
Partition Descriptors
•
Relay Descriptors
DEVICE PROG?
1 = YES 0 = NO 0
For defining the following device characteristics for addressable devices, including keypads, RF
receivers (5881), output relay modules (4204/4204CF), FSA (FSA-8/FSA-24), 4285/4286 VIP Module,
Panel Link Module (VA8201), ECP long range radio (7845C), and VISTA Gateway Module:
•
Device Address
•
Device Type
•
Keypad Options (including Partition assignment)
•
RF House ID
•
LRR Options (including Programming radio)
OUTPUT PGM?
1 = YES 0 = NO 0
For defining output device functions.
RLY VOICE DESCR?
1 = YES 0 = NO 0
For entering voice descriptors for relays to be used with the 4285/4286 VIP Module.
CUSTOM INDEX ?
1 = YES 0 = NO 0
For creating custom word substitutes for VIP Module annunciation.
ACCESS POINT PGM
1 = YES 0 = NO 0
For defining the parameters for each of the VistaKey zones, including which group(s) have access
through an access point (door). See the
VistaKey-SK Installation and Setup Guide
for detailed
programming instructions.
ACCESS GRP PGM
1 = YES 0 = NO 0
For defining the capabilities (privileges) for each group of users. See the
VistaKey-SK Installation and
Setup Guide
for detailed programming instructions.
EVENT/ACTION PGM
1 = YES 0 = NO 0
For defining events and time windows for an access group. See the
VistaKey-SK Installation and Setup
Guide
for detailed programming instructions.
- &RPPHUFLDO%XUJODU\ 1
- Table of Contents 3
- List of Figures 5
- General Description 7
- SECTION 2 11
- Theory of Partitioning 11
- Common Lobby Logic 11
- COMMON LOBBY 12
- Panel Linking 14
- How to Use Panel Linking 15
- Multi-Panel View Mode 17
- Installing the Control 19
- Notes: 20
- Device Programming 21
- #93 Menu 21
- Figure 3-5 21
- Installing External Sounders 22
- Telephone Line Connections 23
- 2-WIRE SMOKE 24
- DETECTOR 24
- Figure 3-11 25
- Tamper Supervision 26
- Installing RPM Devices 27
- Wireless Zone Expansion 28
- Menu Mode 29
- Installing Output Devices 32
- Output Programming 33
- Programming 33
- J7 CONNECTOR 34
- Smoke Detector Reset 35
- Remote Keypad Sounder 35
- #93 Menu Mode 36
- ECP RADIO 37
- CONTROL PANEL 39
- Installation and 40
- Setup Guide 40
- Event Log Connections 41
- Figure 3-37 43
- 4 3 2 1 44
- 8 ohm Speaker 45
- Connecting the Transformer 46
- #93 Menu Mode Programming 52
- Zone Number Designations 54
- Section 4 – Programming 55
- Communication Defaults 55
- Polling Loop Supervision 57
- SECTION 3 57
- SECTION 9: User Access Codes 60
- Programming Guide 61
- Scheduling Options 79
- Time Window Definitions 80
- Windows Programming 82
- Holiday Schedule Programming 82
- Time Windows 83
- Daily Open/Close Schedules 84
- Holiday Schedules 84
- Time-Driven Events 85
- Temporary Schedules 90
- User Code + [#] + 81 91
- to enter this mode 91
- User Scheduling Menu Mode 92
- Downloading Primer 93
- Section 7 – Downloading 95
- On-Line Control Functions 95
- Scheduled Download 96
- Direct-Wire Downloading 96
- Telco Handoff 96
- Setting the Real-Time Clock 97
- User Access Codes 99
- Multiple Partition Access 100
- Exiting the User Edit Mode 102
- Testing the System 103
- Transmitter ID Sniffer Mode 104
- Go/No Go Test Mode 104
- Trouble Conditions 105
- To the Installer 105
- Contacting Technical Support 106
- Regulatory Agency Statements 107
- Requirements 108
- Summary of System Commands 111
- Specifications 113
- APPENDIX D 115
- APPENDIX E 124
- VISTA-128BP 126
- SUMMARY OF CONNECTIONS 126
- VISTA-250BP 127
- ¬.4l 128
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS
Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-20HW Guía para resolver problemas
(100 paginas)
(100 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-10SE Manual de usuario
(24 paginas)
(24 paginas)
(56 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales