ADEMCO Vista-128B PLUS Especificaciones descargar pdf (Pagina 60)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

4-10

Using an RF Transmitter Zone

A button type RF transmitter (5804) can be used to

provide access or egress for up to 4 doors. One button

will control one door. Also, a button can be used to

provide access or egress due to a panic or duress

condition.

An RF transmitter (5816) can be used with a remote

switch to provide exit in case of a fire alarm using a

PassPoint event action. To program the RF transmitter

for access control, perform the following steps:

Step Action

1 Enter Zone Programming in the #93 Menu

Mode.

2 Program the zone with a response type 27

(Access Point).

3 Enter the access point number (00-31) of the

door.

4 Indicate whether RF device is for entry or exit.

5 Enter the partition number

6 Enter the input type: button RF (05).

7 Enter the loop number.

8 Enroll the serial number

See Zone Programming in the Programming Guide for a

detailed explanation.

•

RF buttons and pendants must be assigned

to a user number in order to function. See

SECTION 9: User Access Codes

for the

procedure.

•

An RF transmitter will not provide access or

grant if the system is in any test mode.

Using Wireless Keypads

Wireless keypads (5827 & 5827BD) can provide another

way of entering or exiting the premises. They function

the same as alpha keypads, except when the code + #

73 is entered. This entry will allow momentary access

to ALL access points in the partition to which the

keypad is assigned To program the wireless keypad,

enter the partition the keypad is assigned to in field

1*48.

Control of Lighting and Appliances

Lighting and appliances can be controlled when an

access or exit event occurs. Lights or appliances can be

automatically turned on or off when a valid entry or

egress request is presented at an access point. To

control these devices, the VISTA-128BP/VISTA-250BP

relays or the ACS relays or triggers are used with

keypads and/or RF transmitters whose response type is

Access Point (27).

To program the control of lighting and appliances,

perform the following steps:

Step Action

1 Enter Output Programming in the #93 Menu

Mode.

2 Program all the information for the relay.

3 Select the output type: ECP (1) (4204/4204CF)

or (2) (X-10).

See Output Programming in the Programming Guide

for a detailed explanation.

Using the VISTA-128BP/VISTA-250BP for Stand-

Alone Access Control

The VISTA-128BP/VISTA-250BP can be used for access

control without interfacing to PassPoint ACS or

VistaKey. A user can trigger an access point (i.e., door

strike) for 2 seconds by entering User Code + [0].

To program the VISTA-128BP/VISTA-250BP for Stand-

Alone access control, perform the following steps:

Step Action

1 Enter Output Programming in the #93 Menu

Mode.

2 Program the output type as 1, or 2.

3 For type 1, program the ECP address and

relay number.

4 For type 2, program the house and unit codes.

Program the relay number in field 1

∗

(partition-specific).

See Output Programming in the Programming Guide

for a detailed explanation.

Programming for ECP Long Range Radio Programming for the Event Log

•

Program the LRR in

Device Programming

in the

#93 Menu Mode Programming.

•

Field ✳56: Selects the time the panel should wait

before it attempts to send a message to the second

destination..

•

Field ✳57: Select the initial reporting destination

for messages.

•

Field ✳58: Select events for the primary sub’s ID

•

Field ✳59: Select events for the secondary sub’s ID.

• 1

✳

Event Log Types (

=enable;

=disable for

each type)

• 1

✳

12/24-Hour Time Stamp Format (

=12 hr;

=24 hr)

• 1

✳

Event Log Printer On-line (

=disable;

=enable)

• 1

✳

Printer Baud Rate (

=300;

=1200)

• Event Log Report Codes

System Group #2 in the

#93 Menu Mode

1 2 ... 55 56 57 58 59 60 61 62 63 64 65 ... 127 128

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-128B PLUS Especificaciones Pagina 60

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS