ADEMCO Vista-128B PLUS Especificaciones descargar pdf (Pagina 46)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

3-28

REAL-TIME CLOCK (RTC)

EARTH

GROUND

TYPICAL

CONTROL'S

AC TERMINALS

Figure 3-41: RTC and Ground Connections

YEL (DATA OUT)

RED (+12VDC)

GRN (DATA IN)

BLACK (-) GND

TO CONTROL'S

KEYPAD

TERMINALS

Figure 3-42: TeleSmart to Control Connections

Connecting the Transformer

This product uses the 1361 transformer (1361CN in

Canada). If you are using Powerline Carrier devices,

the 4300 transformer interface must be used instead of

the regular 1361 transformer. The 4300 supplies the

control panel with AC, and also sends control pulses

through the premises electrical system to control the

Powerline Carrier devices.

Use 1361CN Transformer in Canadian

installations.

Power Limiting Outputs

All outputs are power-limited as per UL985/UL1023.

The following table shows the maximum current that

may be drawn from each output.

Output Maximum Current Draw

Auxiliary Power 750mA

Polling Loop 128mA

Alarm Output 1.7A

For Household Fire or Combination Household

Fire/Burglary Installation:

The total current drawn

from the auxiliary power, the polling loop, and the

alarm output combined must not exceed 750mA to

comply with the battery independence requirements in

UL985.

For Household Burglary-Only Installations:

The

total current drawn from the alarm output may be up

to 1.7A. A battery must be installed to supply the

current of the combined auxiliary power, polling loop,

and alarm output in excess of 750mA.

Failure to observe the polling loop current

rating will cause polling loop malfunction.

Failure to observe the auxiliary power current

rating will result in a battery that does not

charge properly or possibly a tripped circuit

breaker.

To connect the transformer to the control, perform the

following steps:

Step Action

1 Connect all installed devices to the control.

2 Wire the 1361 Transformer (1361CN in

Canada) to the panel (before connecting the

battery) as shown in

Figure 3-43

, or wire the

4300 Transformer as shown in

Figure 3-44

(if using Powerline Carrier devices).

3 Plug the transformer into a 24-hour,

uninterrupted, 120VAC, 60Hz outlet. After

a few seconds, the keypad display appears.

NO CONNECTION

TRANSFORMER

16.5VAC, 40VA

ADEMCO No.1361

or 4300, XM10E, or

XF10 if X-10 DEVICES

WILL BE USED.

Connect to

24hr. source

of AC mains

123

RED (+)BLK (-)

Connect to

12VDC, 4AH

or 12VDC, 7AH

GEL CELL

BATTERY

CHARGING

VOLTAGE

13.7 VDC

NOTE:

WHEN POWERING UP

THE PANEL, PLUG THE

TRANSFORMER IN BEFORE

CONNECTING THE BATTERY.

BATTERY

TABS

PRIMARY

POWER

Supplied by a

transformer which

is rated at

16.5VAC, 40VA.

Caution must be

taken when wiring

this transformer to

the panel to guard

against blowing the

fuse inside the

transformer (non-

replaceable).

Figure 3-43: 1321 Transformer and Battery

Connections

123456789

GROUND

OUT 6

IN 2

GROUND

IN 3

GROUND

OUT 5

J8 CONNECTOR

BLACK

BLUE

BROWN

GREEN

RED

WHITE

YELLOW

GRAY

VIOLET

4142TR CABLE

TB1

-1

TB1

-30

TB1

-2

Earth

Ground

Sync

Data

Com

4300 TRANSFORMER/INTERFACE

Figure 3-44: 4300 Transformer Connections

1 2 ... 41 42 43 44 45 46 47 48 49 50 51 ... 127 128

Comentarios a estos manuales

Sin comentarios

ADEMCO Vista-128B PLUS Especificaciones Pagina 46

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS