ADEMCO Vista-128B PLUS Especificaciones Pagina 105
- Pagina / 128
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Section 10 – Testing The System
10-3
Trouble Conditions
Check or Trouble Messages
Display
Description
CHECK or
TRBL
(as per field
1
✳
07)
This indicates that a problem exists on
the zone number displayed. Zone trouble
may be caused by one of the following
conditions:
•
A hardwired fire zone is open
(broken wire).
•
A Day/Night zone (zone type 5) is
faulted.
•
A polling loop zone is not seen by
the control panel.
•
A polling loop zone has been
tampered (cover removed on a
4190).
•
A wireless zone has not checked in
during the time programmed in field
1
✳
31.
•
A 5800 Series transmitter has been
tampered (cover removed).
CHECK 6XX
XX = 01-32
This indicates a trouble on a 4204CF
Supervised Bell Output (corresponding
relay number 01-32).
CHECK 8XX
XX = 00-30
This indicates a trouble on a peripheral
device (connected to the panel’s keypad
terminals) of the corresponding device
address (00-30).
CHECK 9XX
XX = 00-99
This indicates that a system trouble
exists (RF receiver, bell output, etc.).
If the problem has been corrected, enter an
OFF sequence (
Security Code + OFF
) twice to
clear the display.
Power Failure
Display
Description
AC LOSS
POWER
LED is off
This indicates that the system is
operating on battery power only. Check
to see that the circuit breaker for the
branch circuit that your system’s
transformer is wired to has not been
accidentally turned off.
Instruct the
user to call a service representative
immediately if AC power cannot be
restored.
Other System Messages
Display
Description
COMM
FAILURE
This indicates that a failure occurred in
the telephone communication portion of
your system.
LO BAT
This indicates that a low-battery
condition exists in the wireless
transmitter displayed. Pressing any key
silences the audible warning sound.
SYSTEM LO
BAT
This indicates that a low-battery
condition exists with the system’s
backup battery.
RCVR
SETUP
ERROR
This indicates that the system has more
wireless zones programmed than the
wireless receiver can support. If this is
not corrected, none of the zones in the
system will be protected. If additional
wireless zones are desired, use an
appropriate receiver.
MODEM
COMM
This indicates that the control is on-line
with a remote computer.
To the Installer
Regular maintenance and inspection (at least annually)
by the installer and frequent testing by the user are
vital to continuous satisfactory operation of any alarm
system.
The installer should assume the responsibility of
developing and offering a regular maintenance program
to the user as well as acquainting the user with the
proper operation and limitations of the alarm system
and its component parts. Recommendations must be
included for a specific program of frequent testing (at
least weekly) to ensure the system’s proper operation at
all times.
Turning the System over to the User
Fully explain the operation of the system to the user by
going over each of its functions, as well as the User’s
Manual supplied.
In particular, explain the operation of each zone
(entry/exit, perimeter, interior, fire, etc.). Be sure the
user understands how to operate any emergency
feature(s) programmed into the system.
- &RPPHUFLDO%XUJODU\ 1
- Table of Contents 3
- List of Figures 5
- General Description 7
- SECTION 2 11
- Theory of Partitioning 11
- Common Lobby Logic 11
- COMMON LOBBY 12
- Panel Linking 14
- How to Use Panel Linking 15
- Multi-Panel View Mode 17
- Installing the Control 19
- Notes: 20
- Device Programming 21
- #93 Menu 21
- Figure 3-5 21
- Installing External Sounders 22
- Telephone Line Connections 23
- 2-WIRE SMOKE 24
- DETECTOR 24
- Figure 3-11 25
- Tamper Supervision 26
- Installing RPM Devices 27
- Wireless Zone Expansion 28
- Menu Mode 29
- Installing Output Devices 32
- Output Programming 33
- Programming 33
- J7 CONNECTOR 34
- Smoke Detector Reset 35
- Remote Keypad Sounder 35
- #93 Menu Mode 36
- ECP RADIO 37
- CONTROL PANEL 39
- Installation and 40
- Setup Guide 40
- Event Log Connections 41
- Figure 3-37 43
- 4 3 2 1 44
- 8 ohm Speaker 45
- Connecting the Transformer 46
- #93 Menu Mode Programming 52
- Zone Number Designations 54
- Section 4 – Programming 55
- Communication Defaults 55
- Polling Loop Supervision 57
- SECTION 3 57
- SECTION 9: User Access Codes 60
- Programming Guide 61
- Scheduling Options 79
- Time Window Definitions 80
- Windows Programming 82
- Holiday Schedule Programming 82
- Time Windows 83
- Daily Open/Close Schedules 84
- Holiday Schedules 84
- Time-Driven Events 85
- Temporary Schedules 90
- User Code + [#] + 81 91
- to enter this mode 91
- User Scheduling Menu Mode 92
- Downloading Primer 93
- Section 7 – Downloading 95
- On-Line Control Functions 95
- Scheduled Download 96
- Direct-Wire Downloading 96
- Telco Handoff 96
- Setting the Real-Time Clock 97
- User Access Codes 99
- Multiple Partition Access 100
- Exiting the User Edit Mode 102
- Testing the System 103
- Transmitter ID Sniffer Mode 104
- Go/No Go Test Mode 104
- Trouble Conditions 105
- To the Installer 105
- Contacting Technical Support 106
- Regulatory Agency Statements 107
- Requirements 108
- Summary of System Commands 111
- Specifications 113
- APPENDIX D 115
- APPENDIX E 124
- VISTA-128BP 126
- SUMMARY OF CONNECTIONS 126
- VISTA-250BP 127
- ¬.4l 128
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-128B PLUS
Los Sistemas De Control De Acceso De Seguridad ADEMCO Vista-20HW Guía para resolver problemas
(100 paginas)
(100 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-10SE Manual de usuario
(24 paginas)
(24 paginas)
(56 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales