ADEMCO VISTA-120 Guia de preparacion descargar pdf (Pagina 49)

Vista 120 Training Guide 49

6.8 4204 Relay Programming

Training Module

• Set 4204’ DIP switch for an unused device address 01-15.

• Connect 4204 via the flying lead supplied to terminals 6 (RED), 7 (BLACK), 8 (GREEN)

and 9 (YELLOW) of the Vista50P.

Use 6139 console to enter programming mode: installer code + 8 0 0 0

Press # 9 3 to enter Menu Mode.

Press 0 (NO) until “Device Prog?” is displayed, then press 1 (YES).

• Enter the two digit Address Number (01 – 15), as set on the 4204’s Dip Switches

• Press * to move to Device Type

• Enter a Device Type “4” for Output Device

• Press * to move to Supervised CF

• Press * to move to Device Address

• If more than one 4204 is to be used, follow the same procedure until all output devices

have been programmed, enter 0 0 * to exit “DEVICE PROG?”

• Enter * until console displays “RELAY PROG?”, then press 1 (Yes)

• The console will display “ENTER RELAY No.”, enter the relay number 1-4. This is a

reference number only, used for identification purposes. The actual module address and

relay number on the module is programmed in the last two prompts. Press * to continue.

• The console will display a summary START screen.

• Press * and the console will display a summary STOP screen.

• Press * to move to “RELAY ACTION” then enter 0 = not used, 1 = close for 2 secs, 2 =

stay closed to 3 = pulse on/off.

• Press * to move to “START EVENT” then enter 0 = not used, 1 = alarm, 2 = fault, 3 =

trouble or 4 = restore.

• Press * to move to “START ZN LIST” then enter the zone list number (1 to 8) or 0 is a

zone list is not being used.

• Press * to move to “START ZN TYP” then, if a zone type/system operation is being used,

enter the appropriate 2-digit code as listed below.

Choices for Start/Stop Zone

Types

Choices for Start/Stop System

Operation

00 = No Response (Not used) 20 = Arming Stay 41 = **AC Power Fail

01 = Entry/Exit # 1 21 = Arming Away 42 = **System Battery Low

02 = Entry/Exit # 2 22 = Disarming (Code+Off) 43 = Communication Failure

03 = Perimeter 31 = End of Exit Time 44 = RF Low Battery

04 = Interior Follower 32 = Start of Entry Time 45 = Polling Loop Failure

05 = Trouble Day/Alarm Night 34 = Code + # + 71 Key Entry 51 = RF Receiver Failure

06 = 24Hr Silent 35 = Code + # + 72 Key Entry 52 = Kissoff

07 = 24Hr Audible 36 = **At Bell Timeout ** 54 = Fire Zone Reset

08 = 24Hr Aux 37 = 2 Times Bell Timeout 55 = Disarm + 1

09 = Fire Alarm or Trouble 38 = Chime 56 = XX Minutes (enter XX in field 1*74 Stop

condition Only)

10 = Interior w/Delay 39 = Fire Alarm 57 = YY Seconds (enter YY in field 1*75 Stop

condition Only)

23 = No Alarm response

(for output relay activation,

such as for access control)

40 = Bypassing 58 = Duress

*** Or at Disarming, whichever occurs earlier)

1 2 ... 44 45 46 47 48 49 50 51 52 53

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-120 Guia de preparacion Pagina 49

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-120