ADEMCO Security System VISTA-15CN Guia de preparacion Pagina 90
- Pagina / 132
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
VISTA-15/VISTA-15CN Installation and Setup Guide
17–4
CHOICES FOR ZONE TYPES
00 = Not Used 04 = Interior Follower 08 = 24-Hr Aux
01 = Entry/exit #1 05 = Trouble Day/Alarm Night 09 = Fire
02 = Entry/exit #2 06 = 24-Hr Silent 10 = Interior w/Delay
03 = Perimeter 07 = 24-Hr Audible 24 = Silent Burglary
CHOICES FOR SYSTEM OPERATION
20 = Arming–STAY 36 = At Bell Timeout
†
42 = System Battery Low
21 = Arming–AWAY 38 = Chime 43 = Comm Failure
22 = Disarming (Code+OFF) 39 = Any Fire Alarm 52 = Kissoff
31 = End of Exit Time 40 = Bypassing 58 = Duress
32 = Start of Entry Time 41 = AC Power Failure
33 = Any Burglary Alarm
†
Or at Disarming, whichever occurs first.
02 Stop: Zn Lst
No List 0
If a zone list is used to STOP, or restore the device action, enter the
zone list number
1
,
2
, or
3
(to be programmed in
✱
81 mode). If not
used, enter
0
.
Press
[
✱
]
to continue.
02 Stop: Zn Typ
Zone Disabled 00
If a zone type or system operation is used to STOP the device
action, enter the appropriate 2-digit code (refer to
“
CHOICES FOR
ZONE TYPES
”
listed above). If not, enter
00
.
Press the
[
✱
]
key to continue.
02 A EV ZL ZT –
STT 0 0 0 00 –
This screen again displays a summary of the current device START
(STT) programming. Press
[
✱
]
to continue.
02 A EV ZL ZT –
STP – – 0 00 –
This screen again displays a summary of the current device STOP
(STP) programming. Press
[
✱
]
to continue.
02 X10 Device ?
0 = No, 1 = Yes 00
Enter
1
if you are using a Powerline Carrier device (
X10); if not,
enter
0
.
The display then returns to the first screen so that the next
device
number to be programmed can be entered. Enter
00
to end device
programming.
Example of
Output Device
Programming
Assume that a lamp is to be turned on via a
Powerline Carrier
device
(
X10
) when any one of 3 specific zones are faulted, or when
any 24-hour auxiliary zone is faulted. Additionally, assume that you
want to be able to turn off the lamp
manually
without affecting the
arming status of the system.
To program the above example, do the following:
1.
In
✱
80 Interactive mode, choose Output Device 01 and program
the ACTION (A) to be “2” (Stay Closed). Press
[
✱
]
to continue.
The Event you want to START the Device action is a fault, so
program
2
in (EV). Press
[
✱
]
to continue.
To use Zone List 1 for the 3 specific zones, program
1
in (ZL),
and program these 3 zones in
✱
81's Zone List 1. Press
[
✱
]
to
continue.
- 9,67$ 1
- 9,67$&1 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- Installing the Control 13
- V15-01-V0 14
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Section 12: Final Power-Up 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–6 23
- 2000 OHMS 24
- Programming Hardwired Zones 26
- Wired Zone Expansion 27
- DISARMED 29
- READY TO ARM 29
- Wireless Expansion 31
- < < 32
- Installing the 5800TM Module 33
- Jam Detection and Reporting 33
- Appendix A 36
- 1 2 3 4 5 37
- Powerline Carrier Devices 41
- Programming Relay Outputs 42
- 4285 & 4286 VIP Module 43
- Section 11: 44
- Audio Alarm 44
- Verification (AAV) Unit 44
- 4285 or 4286 45
- VIP MODULE 45
- External Sounders 47
- Sounder Connections and Power 48
- Sounder Supervision 48
- Testing the Sounder 48
- Long Range Radio 49
- Dynamic Signaling Feature 50
- 1 2 3 4 5 6 52
- Final Power-Up 53
- Battery Tests 54
- Mechanics of Programming 55
- Loading Factory Defaults 57
- Exiting the Programming Mode 57
- Section 18. Zone Lists 61
- Data Field Descriptions 63
- ZONE SOUNDS & 65
- TIMING ( 65
- Interactive 69
- Zone Programming 77
- 79
- To Remove a Zone 82
- Section 16 - Zone Programming 85
- Output Device Programming 87
- Zone Lists 93
- Cross Zoning - Zone List 04 94
- NIGHT-STAY - Zone List 05 94
- Alpha Descriptor Programming 95
- Summary Mode Display 96
- ALPHA VOCABULARY LIST 98
- CHARACTER (ASCII) CHART 98
- Remote Programming and 99
- Control (Downloading) 99
- Initial Download 100
- Remote Programming Commands 100
- System Communication 101
- FORMAT TYPE DESCRIPTION 102
- System Operation 105
- Keypad Functions 106
- Setting the Real-Time Clock 110
- Testing the System 111
- Troubleshooting Guide 113
- SMOKE DETECTOR 114
- CONTACTING TECHNICAL SUPPORT 115
- In This Section 117
- APPENDIX A 121
- Regulatory Agency Statements 123
- Warnings and Limitations 125
- VISTA-15/VISTA-15CN 131
- SUMMARY OF CONNECTIONS 131
- Copyright 132
- 2000 PITTWAY CORPORATION 132
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15CN
Los Sistemas De Control De Acceso De Seguridad ADEMCO Ademco VISTA-40 Manual de usuario
(20 paginas)
(20 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-50PEN Instrucciones de operaciones
(84 paginas)
(84 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales