ADEMCO Security System VISTA-15CN Guia de preparacion Pagina 53
- Pagina / 132
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
12–1
SECTION 12
Final Power-Up
••••••••••••••••••••••••••••••••••••••••••••••••••
In This Section
♦
Earth Ground Connections
♦
AC Power-Up
♦
Connecting the Backup Battery
♦
Battery Tests
••••••••••••••••••••••••••••••••••••••••••••••••••
Earth Ground Connections
The designated earth ground terminal (25) must be terminated in a good earth ground for
the lightning transient protective devices in this product to be effective. It also must be
grounded to enable the telephone line fault indicator to work properly. The following are
examples of good earth grounds available at most installations:
Metal Cold Water Pipe: Use a noncorrosive metal strap (copper is recommended) firmly
secured to the pipe to which the ground lead is electrically connected and secured.
AC Power Outlet Ground: Available from 3-prong, 120VAC power outlets only. To test the
integrity of the ground terminal, use a 3-wire circuit tester with neon lamp indicators, such
as the UL Listed Ideal Model 61-035, or equivalent, available at most electrical supply stores.
AC Power-Up
To turn on AC power, perform the following steps:
1. Plug the 1321/1321CN or 4300 Transformer into a 24-hour, unswitched 120VAC outlet.
Following power-up, one of the following is displayed: AC, dI (disabled); BUSY
STANDBY (alpha keypads); or NOT READY (fixed-word keypads). The green POWER
LED (or READY LED on some keypads) should light.
2. After approximately 1 minute, the initial displays revert to DISARMED...READY TO
ARM for alpha keypads, or READY for fixed-word keypads (if there are no faulted zones).
This 1-minute delay allows PIRs, etc. to stabilize.
To bypass this delay, press: # + 0.
Connecting the Backup Battery
In the event of an AC power loss, the control panel is supported by a backup, rechargeable
Sealed Lead Acid battery. The range of battery sizes recommended are: 12VDC; 4AH-
17.2AH. See
"Calculating the Battery Size Needed"
below. The battery is installed in the
control cabinet.
U
L
Use a 4AH battery or larger for UL installations. Refer to
next page to calculate the actual battery
size needed.
The standby battery is automatically tested every 4 hours, beginning 4 hours after exiting
Programming mode. In addition, entry into the Test mode causes a battery test to be
initiated.
- 9,67$ 1
- 9,67$&1 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- Installing the Control 13
- V15-01-V0 14
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Section 12: Final Power-Up 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–6 23
- 2000 OHMS 24
- Programming Hardwired Zones 26
- Wired Zone Expansion 27
- DISARMED 29
- READY TO ARM 29
- Wireless Expansion 31
- < < 32
- Installing the 5800TM Module 33
- Jam Detection and Reporting 33
- Appendix A 36
- 1 2 3 4 5 37
- Powerline Carrier Devices 41
- Programming Relay Outputs 42
- 4285 & 4286 VIP Module 43
- Section 11: 44
- Audio Alarm 44
- Verification (AAV) Unit 44
- 4285 or 4286 45
- VIP MODULE 45
- External Sounders 47
- Sounder Connections and Power 48
- Sounder Supervision 48
- Testing the Sounder 48
- Long Range Radio 49
- Dynamic Signaling Feature 50
- 1 2 3 4 5 6 52
- Final Power-Up 53
- Battery Tests 54
- Mechanics of Programming 55
- Loading Factory Defaults 57
- Exiting the Programming Mode 57
- Section 18. Zone Lists 61
- Data Field Descriptions 63
- ZONE SOUNDS & 65
- TIMING ( 65
- Interactive 69
- Zone Programming 77
- 79
- To Remove a Zone 82
- Section 16 - Zone Programming 85
- Output Device Programming 87
- Zone Lists 93
- Cross Zoning - Zone List 04 94
- NIGHT-STAY - Zone List 05 94
- Alpha Descriptor Programming 95
- Summary Mode Display 96
- ALPHA VOCABULARY LIST 98
- CHARACTER (ASCII) CHART 98
- Remote Programming and 99
- Control (Downloading) 99
- Initial Download 100
- Remote Programming Commands 100
- System Communication 101
- FORMAT TYPE DESCRIPTION 102
- System Operation 105
- Keypad Functions 106
- Setting the Real-Time Clock 110
- Testing the System 111
- Troubleshooting Guide 113
- SMOKE DETECTOR 114
- CONTACTING TECHNICAL SUPPORT 115
- In This Section 117
- APPENDIX A 121
- Regulatory Agency Statements 123
- Warnings and Limitations 125
- VISTA-15/VISTA-15CN 131
- SUMMARY OF CONNECTIONS 131
- Copyright 132
- 2000 PITTWAY CORPORATION 132
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15CN
Los Sistemas De Control De Acceso De Seguridad ADEMCO Ademco VISTA-40 Manual de usuario
(20 paginas)
(20 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-50PEN Instrucciones de operaciones
(84 paginas)
(84 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales