ADEMCO Security System VISTA-15CN Guia de preparacion descargar pdf (Pagina 61)

Section 14 - Zone Response Type Definitions

14–3

Type 10

Interior w/Delay

This zone type gives

Entry Delay

(using the programmed entry

time), if tripped when the panel is armed in the AWAY mode. Entry

Delay begins whenever sensors in this zone are violated, regardless

of whether or not an Entry/Exit Delay zone was tripped first. No

Entry Delay is provided if tripped when the panel is armed in the

MAXIMUM mode. Exit Delay is present for any arming mode. This

zone type is bypassed when the panel is armed in the STAY

or INSTANT mode. If the panel is armed NIGHT-STAY, this

zone type is not bypassed if it is on the NIGHT-STAY Zone List

05.

Type 12

24 Hour Monitor

This zone type is a dynamic monitor of a zone fault/trouble. In the

case of a short/open, the message, "*ALARM*-24 Hr. Non-Burg. -

#XXX " (where XXX is the zone number) is sent to the Central

Station. The system keypad displays a fault message indicating the

appropriate zone. Upon restoral of the zone, the message,

"*RESTORE*-24 Hr. Non-Burg. -#XXX " is sent to the Central

Station. The fault message automatically disappears from the

keypad. The zone restores dynamically; therefore, a User Code +

OFF sequence is not needed to reset the zone. Faults of this zone

type are independent of the system, and can exist at the time of

arming without interference.

If you want to use this zone type to activate a relay, all zones of

Type 12 must be placed into a zone list and triggered by a “fault”

event. The same zone list must be programmed for the “STOP”

event. A restore of every faulted zone in that zone list is required to

deactivate the

relay

Type 20

Arm-STAY

This is a special-purpose zone type, used with 5800 Series Wireless

Pushbutton units, which results in arming the system in the STAY

mode when the zone is activated. Pushbutton units send the zone

number as a user number to the Central Station when arming or

disarming.

Type 21

Arm-AWAY

This is a special-purpose zone type, used with 5800 Series Wireless

Pushbutton units, which results in arming the system in the AWAY

mode when the zone is activated. Pushbutton units send the zone

number as a user number to the Central Station when arming or

disarming.

Type 22

Disarm

This is a special-purpose zone type, used with 5800 Series Wireless

Pushbutton units, which results in disarming the system when the

zone is activated.

Type 23

No Alarm Response

This zone type can be used on a zone when an output relay action is

desired, but with no accompanying alarm (e.g., lobby door access).

Type 24

Silent Burglary

This zone type provides an instant alarm, with no audible

indication at any keypad or external sounder, if the zone is faulted

when the system is armed in the AWAY, STAY, NIGHT-STAY,

INSTANT, or MAXIMUM mode. This zone type is usually assigned

to all sensors or contacts on exterior doors and windows where bells

and/or sirens are NOT desired. A report is sent to the Central

Station.

All of the zone types described are available for the wireless portion of the system, if used.

The reaction of a zone type is changed if the zone itself is included in either Zone List 04 or Zone

List 05. See

Section 18. Zone Lists

for further explanation.

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 131 132

Comentarios a estos manuales

Sin comentarios

ADEMCO Security System VISTA-15CN Guia de preparacion Pagina 61

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15CN