ADEMCO Security System VISTA-15CN Guia de preparacion descargar pdf (Pagina 113)

24–1

SECTION 24

Troubleshooting Guide

••••••••••••••••••••••••••••••••••••••••••••••••••

SYSTEM (including Wireless)

SYMPTOM POSSIBLE CAUSE REMEDY

1. Transmitter signal not

received at

5881/5882.

1a. Transmitter or 5881/5882 not properly

powered.

1a Check or change transmitter's battery.

Check VISTA-15/VISTA-15CN's AC

power.

1b. If transmitter

5827/5827BD

: House

Code not set in field

✱

24, or transmitter

not set to same House Code set in that

field.

1b. Check code switches inside transmitter.

Must match with RF House Code

programmed in VISTA-15/VISTA-

15CN.

1c. Transmitter located too far from RF

receiver.

1c. Move transmitter or RF receiver.

1d. Metal shielding between transmitter and

RF receiver.

1d. Check for large metal obstructions,

then relocate transmitter if necessary.

1e. Transmitter malfunctioning. 1e. Verify by activating 5881/5882 with

another, similar transmitter. If OK

now, return defective transmitter.

1f. 5881/5882 malfunctioning. 1f. Verify by making sure other

transmitters cannot activate 5881/5882.

If defective, replace and return original

5881/5882.

1g. Transmitter no. (zone) not programmed. 1g. Verify programming.

1h. 5881/5882 address incorrect. 1h. Set DIP switch on 5881/5882 for

address “0.”

1i. Field

✱

22 not set properly. 1i. Set field

✱

22 for “1.”

2. Transmitter zone number

appears during Transmitter

Sniffer mode, but does not

clear.

2a. Transmitter zone type (ZT) is set to

(Not Used).

2b. Transmitter battery not installed.

2a. Set ZT to a valid active zone type in

field

✱

56 or

✱

58.

2b. Install proper battery.

2c. 5800 system transmitter not

enrolled

system.

2c. Enroll unit in field

✱

56 or

✱

58.

3. LOW BATTERY message on

keypad

3a.

Bat

System Lo Ba

t (no zone nos.):

System battery is low or missing.

3b.

Bat

Lo Bat

: Remote RF keypad

battery is low.

3a. Verify that battery charging circuit is

working. If OK, replace battery.

3b. Replace remote RF keypad battery.

3c.

Bat

Lo Bat

: Transmitter for zone

“nn” has a low battery.

3c. Replace transmitter battery in zone

"nn."

4. Periodic beep(s) from

keypad.

4a. System is in Test mode.

4b. A transmitter low battery has occurred

and is displayed.

4c. A supervision Check has occurred.

4a. Enter [Code] + [1] OFF to exit Test

mode.

4b. Enter [Code] + [1] OFF and replace the

battery.

4c. Check the transmitter indicated.

Restore communication to the receiver

to cancel the condition.

5. With 5800 system, no

response to a transmitter in

normal operation, although

zone number clears during

Transmitter Sniffer mode.

5a. Put control in Test mode. If zone does not

respond, try operating the tamper switch

or another input to the transmitter.

If another input causes the zone to be

displayed, the wrong input was

enrolled

when programming.

5a. Delete input's serial number (not the

zone), and enroll the proper input (see

field

✱

56 or

✱

5b. If no response at all from this transmitter,

this physical transmitter has not been

enrolled by the system. Transmitter

Sniffer display is being cleared by another

unit programmed for this zone.

5b. Determine which transmitter is

programmed for this zone and

reprogram as necessary.

1 2 ... 108 109 110 111 112 113 114 115 116 117 118 ... 131 132

Comentarios a estos manuales

Sin comentarios

ADEMCO Security System VISTA-15CN Guia de preparacion Pagina 113

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15CN