ADEMCO Security System VISTA-15CN Guia de preparacion Pagina 21
- Pagina / 132
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Section 3 - Installing Remote Keypads
3–3
Make connections directly to the screw terminals as shown in Figure 7. Make no connection to the
keypad blue wire (if present).
Be sure to connect the negative (–) terminal on the Power Supply unit to terminal 4 (AUX – ) on the
control.
+
–
+
456 7
SUPPLEMENTARY
POWER SUPPLY
–
CONTROL TERMINAL STRIP
AUX.
AUX. DATA
IN
DATA
OUT
IMPORTANT:
MAKE THESE
CONNECTIONS
DIRECTLY TO
SCREW
TERMINALS AS
SHOWN.
TO KEYPAD RED WIRE
TO KEYPAD BLK WIRE
TO KEYPAD YEL WIRE
TO KEYPAD GRN WIRE
TO KEYPAD BLK WIRE
TO KEYPAD RED WIRE
TO KEYPAD GRN WIRE
TO KEYPAD YEL WIRE
Figure 7. Using a Supplementary Power Supply for Keypads
Preliminary Checkout Procedure
To verify that the system is working before connecting field wiring from zones and devices, do
the following:
1.
Temporarily connect a 2000-ohm end-of-line resistor across each of the basic hardwired
zones 1–6, as shown in the VISTA-15/VISTA-15CN Summary of Connections diagram.
Without actual zone wiring or
EOL resistors
connected, the keypads will not display the
READY
message.
2.
Power up the system temporarily by plugging the AC transformer (previously wired to
the control) into a 120VAC outlet.
Busy
–
Standby (on alpha keypads) or dI (on fixed-word keypads) is displayed.
3.
Wait approximately 1 minute. At that time, the green READY LED (or POWER LED on
some types of keypads) should light, and the word READY (on fixed-word keypads), or
DISARMED...READY TO ARM
(on alpha keypads) should be displayed.
To bypass the 1-minute delay, press
[#]
plus
[0].
If the
READY
display does not appear on any of the keypads in the system, or a
NOT
READY
message is displayed, check the keypad wiring connections, and make sure each of
the 6 basic hardwired zones has a 2000 ohm resistor connected across its terminals.
When
READY
is displayed on the keypad(s), the system is functioning properly.
Do not remove the EOL resistors until you are ready to make connections to the hardwired
zones, to allow for testing later in the manual.
If an OC or OPEN-CIRCUIT message is displayed on the keypad, data from the control is not
reaching the keypad. Check the wiring.
- 9,67$ 1
- 9,67$&1 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- Installing the Control 13
- V15-01-V0 14
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Section 12: Final Power-Up 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–6 23
- 2000 OHMS 24
- Programming Hardwired Zones 26
- Wired Zone Expansion 27
- DISARMED 29
- READY TO ARM 29
- Wireless Expansion 31
- < < 32
- Installing the 5800TM Module 33
- Jam Detection and Reporting 33
- Appendix A 36
- 1 2 3 4 5 37
- Powerline Carrier Devices 41
- Programming Relay Outputs 42
- 4285 & 4286 VIP Module 43
- Section 11: 44
- Audio Alarm 44
- Verification (AAV) Unit 44
- 4285 or 4286 45
- VIP MODULE 45
- External Sounders 47
- Sounder Connections and Power 48
- Sounder Supervision 48
- Testing the Sounder 48
- Long Range Radio 49
- Dynamic Signaling Feature 50
- 1 2 3 4 5 6 52
- Final Power-Up 53
- Battery Tests 54
- Mechanics of Programming 55
- Loading Factory Defaults 57
- Exiting the Programming Mode 57
- Section 18. Zone Lists 61
- Data Field Descriptions 63
- ZONE SOUNDS & 65
- TIMING ( 65
- Interactive 69
- Zone Programming 77
- 79
- To Remove a Zone 82
- Section 16 - Zone Programming 85
- Output Device Programming 87
- Zone Lists 93
- Cross Zoning - Zone List 04 94
- NIGHT-STAY - Zone List 05 94
- Alpha Descriptor Programming 95
- Summary Mode Display 96
- ALPHA VOCABULARY LIST 98
- CHARACTER (ASCII) CHART 98
- Remote Programming and 99
- Control (Downloading) 99
- Initial Download 100
- Remote Programming Commands 100
- System Communication 101
- FORMAT TYPE DESCRIPTION 102
- System Operation 105
- Keypad Functions 106
- Setting the Real-Time Clock 110
- Testing the System 111
- Troubleshooting Guide 113
- SMOKE DETECTOR 114
- CONTACTING TECHNICAL SUPPORT 115
- In This Section 117
- APPENDIX A 121
- Regulatory Agency Statements 123
- Warnings and Limitations 125
- VISTA-15/VISTA-15CN 131
- SUMMARY OF CONNECTIONS 131
- Copyright 132
- 2000 PITTWAY CORPORATION 132
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15CN
Los Sistemas De Control De Acceso De Seguridad ADEMCO Ademco VISTA-40 Manual de usuario
(20 paginas)
(20 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-50PEN Instrucciones de operaciones
(84 paginas)
(84 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales