ADEMCO Security System VISTA-15CN Guia de preparacion descargar pdf (Pagina 114)

VISTA-15/VISTA-15CN Installation and Setup Guide

24–2

SYSTEM (including Wireless - cont'd)

SYMPTOM

POSSIBLE CAUSE REMEDY

6. Nuisance or phantom

alarm.

6a. Sensors not properly installed, wired, or

monitored.

6a. Check installation to see if in accordance

with established procedure.

6b. Universal transmitter 5817) programmed

wrong.

6b. Check programming switches on

transmitter.

7. Intrusion alarm for no

apparent reason.

7a. Protected door or window opened while

system armed.

7a. Check with all occupants of protected

home.

7b. Improper user operation of exit/entry

delays.

7b. Check setting of entry and exit delays.

7c.

Magnets

located too far from switches,

and/or doors and windows not properly

aligned.

7c. Check all openings for proper switch and

magnet orientation.

8. “CHECK” and zone number

2–6 are displayed.

8a. Control has sensed a high-resistance

condition on a loop in one of the

hardwired zones (2–6).

8b. Control has sensed a short on one of the

hardwired zones (2–6), and the Hardwire

Short Detection field, ✱30, is enabled.

8a. Check the sensor or the loop wiring in

the affected zone. The system will not

arm until this condition is corrected (or

the affected zone is bypassed).

8b. Check the sensor or the loop wiring in

the affected zone for a short(s). The

system will not arm until this condition

is corrected (or the affected zone is

bypassed).

CONTROL

SYMPTOM POSSIBLE

CAUSE REMEDY

1. AC POWER light off.

1a. Interrupted AC power supply. 1a. Check transformer connection and

powerline circuit breaker.

2. Digital communicator

message not being received.

2a. VISTA-15/VISTA-15CN in Test mode.

2b. Telephone connection not secure.

2c. Digital communicator malfunctioning.

2d. Telephone number in program needs

prefix or access code.

2e. Telephone call to central monitoring

station requires operator assistance.

2a. Remove from Test mode.

2b. Check all connections.

2c. Check with a different VISTA-15/VISTA-

15CN.

2d. Program prefix or access code into the

VISTA-15/VISTA-15CN.

2e. VISTA-15/VISTA-15CN system cannot

work in this situation.

3. Does not arm properly.

3a.

READY

light not on. 3a. Check for faulted zones and make intact,

or use Bypass arming, if desired.

4. VISTA-15/VISTA-15CN

doesn't respond to

keystrokes on keypad.

4a.

CC

or

MODEM COMM

displayed:

System is in communication with

downloader at Central Station.

4b.

dI

or

SYSTEM BUSY

displayed: System

has just been powered and is in its 1-

minute initialization.

4c.

E4

or

E8

displayed: More zones have

been programmed than the zone

expansion modules can handle.

4d. Keypad address setting incorrect.

4a. Wait until download session is finished.

4b. To bypass this time, press [#] + [0].

4c. Delete some zones or use a higher

capability RF receiver.

4d. Keypads must be set for address 31 (non-

addressable mode).

SMOKE DETECTOR

SYMPTOM POSSIBLE

CAUSE REMEDY

1. Detector alarms, no

apparent reason.

1a. Dust, dirt in sensing chamber.

1b. Improper location.

1c. Unit malfunctioning.

1a. Clean unit's sensing chamber with

vacuum cleaner per unit's instructions.

1b. See unit's instructions for locations to

avoid. Relocate as necessary.

1c. Replace detector.

2. Detector's siren sounds.

2a. Unit not receiving required power.

2b. Unit malfunctioning.

2a. Check for proper installation of battery.

Try new battery.

2b. Replace detector.

1 2 ... 109 110 111 112 113 114 115 116 117 118 119 ... 131 132

Comentarios a estos manuales

Sin comentarios