ADEMCO Security System VISTA-15CN Guia de preparacion Pagina 87
- Pagina / 132
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
17–1
SECTION 17
Output Device Programming
(
✱
80 Menu Mode)
••••••••••••••••••••••••••••••••••••••••••••••••••
In This Section
♦
Programming Options Defined
♦
Programming Output Relays and Powerline
Carrier Devices
••••••••••••••••••••••••••••••••••••••••••••••••••
Programming Options Defined
The following definitions will help you understand the programming of output devices when
using
✱
80 and
✱
81 modes. The options used to start and stop these devices are described
below, followed by the actual screen prompts and available entries.
Relays and output devices are not recommended for life safety applications.
The letter(s) in parentheses after each function described below, such as (A) after ACTION,
are those that appear in the various summary displays of programmed data during
programming.
ACTION (A) The ACTION of the device is how the device responds when it is activated
by the Start programming. There are four different choices of actions:
• Close for 2 Seconds (Relay is energized for 2-seconds and then reset).
• Stay closed (Relay is energized until de-energized by another event).
• 1 second On/Off (Relay is alternately energized and de-energized for 1-
second at a time until this action is totally stopped by another event).
• No Response (Relay is not being used).
START (STT) The START programming determines when and under what conditions the
device is activated. The following Start options are available:
Start
by Event
1.
Event
(EV) is the condition (alarm, fault, trouble) that must occur to a
zone or group of zones (a zone list) in order to activate the device. These
conditions apply only when a zone list is used. The different choices for
Event are listed below.
• ALARM......... Relay activates upon any alarm in an assigned zone in
the zone list.
• FAULT.......... Relay activates upon any opening or short in an assigned
zone in the zone list.
• TROUBLE .... Relay activates upon any trouble condition in an assigned
zone in the zone list.
• NOT USED... Relay action is not dependent upon one of the above
events.
- 9,67$ 1
- 9,67$&1 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- Installing the Control 13
- V15-01-V0 14
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Section 12: Final Power-Up 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–6 23
- 2000 OHMS 24
- Programming Hardwired Zones 26
- Wired Zone Expansion 27
- DISARMED 29
- READY TO ARM 29
- Wireless Expansion 31
- < < 32
- Installing the 5800TM Module 33
- Jam Detection and Reporting 33
- Appendix A 36
- 1 2 3 4 5 37
- Powerline Carrier Devices 41
- Programming Relay Outputs 42
- 4285 & 4286 VIP Module 43
- Section 11: 44
- Audio Alarm 44
- Verification (AAV) Unit 44
- 4285 or 4286 45
- VIP MODULE 45
- External Sounders 47
- Sounder Connections and Power 48
- Sounder Supervision 48
- Testing the Sounder 48
- Long Range Radio 49
- Dynamic Signaling Feature 50
- 1 2 3 4 5 6 52
- Final Power-Up 53
- Battery Tests 54
- Mechanics of Programming 55
- Loading Factory Defaults 57
- Exiting the Programming Mode 57
- Section 18. Zone Lists 61
- Data Field Descriptions 63
- ZONE SOUNDS & 65
- TIMING ( 65
- Interactive 69
- Zone Programming 77
- 79
- To Remove a Zone 82
- Section 16 - Zone Programming 85
- Output Device Programming 87
- Zone Lists 93
- Cross Zoning - Zone List 04 94
- NIGHT-STAY - Zone List 05 94
- Alpha Descriptor Programming 95
- Summary Mode Display 96
- ALPHA VOCABULARY LIST 98
- CHARACTER (ASCII) CHART 98
- Remote Programming and 99
- Control (Downloading) 99
- Initial Download 100
- Remote Programming Commands 100
- System Communication 101
- FORMAT TYPE DESCRIPTION 102
- System Operation 105
- Keypad Functions 106
- Setting the Real-Time Clock 110
- Testing the System 111
- Troubleshooting Guide 113
- SMOKE DETECTOR 114
- CONTACTING TECHNICAL SUPPORT 115
- In This Section 117
- APPENDIX A 121
- Regulatory Agency Statements 123
- Warnings and Limitations 125
- VISTA-15/VISTA-15CN 131
- SUMMARY OF CONNECTIONS 131
- Copyright 132
- 2000 PITTWAY CORPORATION 132
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15CN
Los Sistemas De Control De Acceso De Seguridad ADEMCO Ademco VISTA-40 Manual de usuario
(20 paginas)
(20 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-50PEN Instrucciones de operaciones
(84 paginas)
(84 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales