64
SYSTEM COMMUNICATIONS
REPORTS
Reports are transmitted using the programmed format. When a report is
transmitted, up to 4 message rounds are sent. After each round, the
communicator looks for the receiver’s kissoff tone. if the kissoff tone is not
detected, the communicator will pause for 2 seconds before transmitting the
next round. If kiss-off is not heard after the four rounds, the communicator will
hang up and redial to try again.
- 8. COMMUNICATION FORMATS -
IMPORTANT!:
l
Up to 15 eventskones and uiers can be unlqueiy reported
using 3+114+114+2 Ademco Low Speed, SescoalRadionlcs
or Ademco Hlgh Speed
(DTMF)
formats.
l
Up to 27 events/zones and 15 users can be uniquely
reported using 4+2 Express (685 Receiver requires Rev. 4.3
or higher software) or 4+2 Expanded Zone reporting
(Ademco Low Speed, SescoalRadionics).
l
Up to 64 events/zones and 22 users can be uniquely
reported uslng Ademco’s Contact ID format (685 Receivier
requires Rev. 4.4 or hlgher software).
TYPES
The VISTA XM Controls can send reports in any of the following
communication formats:
l
3+1&l ADEMCO LOW SPEED, 10 pps, standard or expanded.
l
3+1&l SESCOA/RADIONICS, 20 pps, standard or expanded.
l
4+2, ADEMCO 10 pps or SESCOAlRADlONICS 2Opps. standard or expanded
l
4+2, EXPRESS (ADEMCO proprietary, DTMF)
l
CONTACT ID (ADEMCO proprietary, DTMF)
n
.’ -.
l
ADEMCO HIGH SPEED (DTMF)
ADEMCO LOW SPEED
ADEMCO LOW SPEED is a pulsed format which responds to a 1400
Hz
handshake and kiss-off, and transmits data with 1900Hz pulse tones @ 10
pulses per second (pps). A typical message consists of two rounds which
must be,verified by the receiver. If both rounds match, the message is
validated, and kissed off. A complete standard report consists of either a 3 or
4digit account
number
followed by a l-digit alarm code. Even though 2
rounds are sent, only the valid report is displayed on the receiver:
Ex:1234 3
In expanded reporting, two messages are sent, two rounds per message, the
first being the account number and alarm code, the second being the zone
(or channel) to which the alarm was assigned. A complete expanded report
consists of a 3 or a-digit account number followed by a ldigit alarm code,
then the alarm code is repeated, followed by the channel number:
Ex:l 234 3 (code3)
3 3 3 3 9 (channel9)
To enable Ademco Low Speed reporting, enter a 0 in “46. To enable
expanded lw speed, enter
1
in ‘55-•60 for the desired expanded reports.
SESCOAIRADIONICS
Standard and expanded reporting in the SESCOAlRADlONlCS format is
virtually the same as ADEMCO Lw Speed except for the following:
1.
The handshake and
kiss-off frequency is 2300 Hz.
2. The data is transmitted with 1800 Hz pulse tones.
3. The rate of transmission is 20 pps.
To enable SESCOAlRADlONlCS reporting, enter a
1 in
‘46. To enable
expanded reporting, enter
1 in
‘55’60 for the desired expanded reports.
A.
ADEMCO’s VISTA XM SERIES TECHNKAL REFERENCE MANUAL
WWW.DIYALARMFORUM.COM
(39 paginas)
(173 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales