ADEMCO 5130XM Manual de instrucciones descargar pdf (Pagina 59)

SYSTEM OPERAnON

- B. KEYPAD FUNCTIONS -

INTRODUCTION

DISARMED

NOT READY

ARMING: AWAY

(CODE + AWAY)

ARMING: STAY

(CODE + STAY)

ARMING: INSTANT

(CODE + INSTANT)

ARMING: MAXIMUM

(CODE + MAXIMUM)

DISARMING

(CODE + OFF)

BYPASSING ZONES

(CODE + BYPASS +

ZONE NUMBER)

The VISTA XM system provides four modes of burglary protection: STAY,

AWAY, INSTANT, and MAXIMUM. In addition, if any zones are faufted pffor fo

arming (NOT READY wncfitiin). the console can dspfay them one at a time,

and specific zones can be sefecfivefy bypassed.

When an alarm occurs, wnsofe sounding and external sounding will occur,

and the zone(s) in alarm will be displayed on the console.

Pressing any key

will silence the wnsole sounder for 10 seconds. Disarming the system will

silence both console and external sounders. When the system is disarmed,

any zones that were in an alarm condition during the armed period will bs

displayed (memory of alarm). To clear thisdisplay. simply repeat the disarm

sequence (enter the securfty code and press the OFF key).

The VISTA XM consoles also feature chime annunciation, and 3 panic key

pairs (for silent, audibie, fire or personal emergency alarms) which can notify

the central station of an atann wndiion, if that service is connected.

Note that ff QUICK ARM is enabled (field ‘29). the [#] key can be pressed

instead of entering the security code, for any of the arming procedures listed

below (Away, Stay, Instant, Maximum).

Before armlng, the system must be In the READY wndition.(all zones must

be intact). If the ‘NOT READY message appears, press the READY r] key to

display all faulted zones.

This mode arms all protection zones, interior and perimeter and provides

entry/exit delays.

Enter the security code and press the AWAY key.

This mode arms perimeter zones only, allowing free movement inside, and

provides entry/exit delays.

Enter the secutfty code

and

press the STAY key.

This mode Is similar to STAY mode, but INSTANT mode eliminates the entry

delays. Exit delay remains.

Enter the sewrity code and press the INSTANT key.

This mode Is simiiar to AWAY mode. but MAXIMUM mode eliminates the entry

delays. Exit delay remains.

Enter the security wde and press the MAXIMUM key.

To disarm the system and silence aiann sounder.

Enter the security wde and press the OFF key.

If desired, the system can be armed with one or more zones left unprotected

(bypassed). To bypass zones, first be sure the system is disarmed. Enter the

security code, press the BYPASS key, and then enter all the zone number(s)

(using 2-digit entries) that are to be bypassed. Single digit zone numbers

must be preceded by a zero (i.e. 01 for zone 1, etc.). After all entries are

made, the console will display the bypassed zones one at a time. Once zones

have been displayed, the system can be armed as usual. Failure to wait for

the sequential display can result in the loss of the bypasses. Bypasses are

removed when the system is .disarmed. Note that Fire zones cannot be

bypassed.

To display bypassed zones (before arming the system), enter the security

code and press the BYPASS key. All bypassed zones will be displayed

sequentially.

Ammcob VISTA xm SERIES TECHNICAL REFERENCE

MANUAL

WWW.DIYALARMFORUM.COM

1 2 ... 54 55 56 57 58 59 60 61 62 63 64 ... 158 159

Comentarios a estos manuales

Sin comentarios

ADEMCO 5130XM Manual de instrucciones Pagina 59

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 5130XM