ADEMCO VISTA-250FBP Guia de preparacion descargar pdf (Pagina 79)

Section 5 – Data Field Descriptions

5-15

FIELD TITLE and DATA ENTRIES EXPLANATION

3*19

Auxiliary Input Alternate

Function Enable

0 = disable

1 = enable

If enabled, pins 5 and 9 on the J2 connector function as RS232 output and

input, respectively. If disabled, they function as fire alarm trigger and

communications device Xmit Okay. See the chart at field 3*20 for the J2

trigger configurations.

NOTE: If field 3*19 is enabled, you cannot use a communications device

connected to the J2 trigger.

3*20

Trigger Outputs Function

Selection

0 = remote keypad sounder

1 = keyswitch LEDs

Select the function of the J2 trigger outputs. See chart below.

J2 Pin

Field 3*19 = 0

Field3*20 = 0

Field 3*19 = 0

Field3*20 = 1

Field 3*19 = 1

1 Panic Alarm Panic Alarm As selected in field 3*20

2 Trouble Trouble As selected in field 3*20

3 Burglary Alarm Burglary Alarm As selected in field 3*20

4 Fire Supervisory Fire Supervisory As selected in field 3*20

5 Fire Alarm Fire Alarm RS232 Output

Remote Console

Sounder

Keyswitch Ready LED As selected in field 3*20

7 Open/Close Keyswitch Armed LED As selected in field 3*20

8 Ground Ground Ground

9 Communicator Xmit Okay Communicator Xmit Okay RS232 Input

3*21

Maximum Number of Dialer

Attempts

Enter the number of dialing attempts 1-8.

Select the maximum number of dialer attempts for the system.

NOTE: Must be 3, 4, or 5 for NFPA 72 compliant systems if a secondary

phone number is programmed.

3*30

Dialer Selection

0 = disable

1 = enable

This field has two entries, one for each dialer (main and backup). Enter 1 if the

dialer is being used.

NOTE: If 3*30 is disabled (0, 0), the panel does not report at all via

communications device.

3*31

Backup Dialer TouchTone or

Rotary

0 = rotary

1 = touchtone

Select the dialing method for the backup dialer.

3*50

Zone Type Restore Enables for

Types 16-18

0 = disable

1 = enable

This field has three entries, one for each zone type. Select the zone types that

will send Restore reports.

Must be 1 for UL commercial fire and burglary installations

3*55

Reset on Second OFF for Bell 1

0 = disable

1 = enable

If enabled, the system silences bell 1 output when the second User Code +

OFF Code is entered after a fire alarm. If disabled, the system silences bell 1

output after the first User Code + OFF.

3*56

Reset on Second OFF for Bell 2

0 = disable

1 = enable

If enabled, the system silences bell 2 output when the second User Code +

OFF Code is entered after a fire alarm. If disabled, the system silences bell 2

output after the first User Code + OFF.

3*57

Confirmation of Arming Ding Bell

2 & Auxiliary Relay

0 = disable

1 = enable

This field has two entries, one for bell 2 and one for the auxiliary relay. If

enabled, produces ½-second external alarm sounding (“ding”) at the end of

exit delay (or after kissoff from the central station, if sending closing reports).

NOTE: If using a keyfob, when the button is pressed, either for arming or

disarming, the bell will ding indicating that the button is working.

Must be 1 for Commercial Burglary installations.

1 2 ... 74 75 76 77 78 79 80 81 82 83 84 ... 135 136

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-250FBP Guia de preparacion Pagina 79

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-250FBP