ADEMCO VISTA-250FBP Guia de preparacion descargar pdf (Pagina 16)

VISTA-128FBP/VISTA-250FBP Installation and Setup Guide

1-2

Arming/Disarming and Bypassing

• Can arm the system with zones faulted (Vent Zone). These zones are automatically bypassed and can be

programmed to automatically unbypass when the zone restores.

• Can arm with entry/exit and interior type zones faulted (Arm w/Fault). These zones must be restored before the exit

delay expires, otherwise an alarm is generated.

• Vent zones cannot be used in UL installations.

• You must disable the Force Arm option (used in conjunction with the Arm w/Fault option), in UL installations.

• Provides global arming capability (ability to arm all partitions the user code has access to in one command).

• Can Quick Exit an armed premises without having to disarm and then rearm the system.

• Can be armed in one of three STAY modes or Instant modes, automatically bypassing specific burglary zones

regardless of the zone response type.

• Can automatically bypass specific zones if no one exits the premises after arming (Auto-STAY). Auto-STAY will not

occur if the system is armed via an RF transmitter, scheduling, keyswitch or downloading.

• Can bypass a group of zones with one set of keystrokes.

• Supports Exit Error Logic, whereby the system can tell the difference between a regular alarm and an alarm caused

by leaving an entry/exit door open. If the system is not subsequently disarmed, faulted entry/exit zone(s) and/or

interior zones are bypassed and the system arms.

• Supports Recent Close report, which is designed to notify the central station that an alarm has occurred within 2

minutes after the exit delay has expired.

Partitioning

• Can control 8 separate areas (partitions) independently, each functioning as if it had its own separate control. All

fire zones must be assigned to partition 1.

• Provides a Common Lobby partition, which can be programmed to arm automatically when the last partition is

armed, and to disarm when the first partition is disarmed.

• Provides a Master partition (9), used for the purpose of viewing the status of all partitions at the same time.

• Can display fire, burglary, panic, and trouble conditions at all other partitions’ keypads (selectable option).

Scheduling

• Can automate system functions, such as arming, disarming, and activation of outputs (e.g., lights).

• Provides access schedules (for limiting system access to users by time).

• Provides an End User Output Programming Mode, allowing the user to control outputs.

System Communication

• Provides supervision of the phone lines (main and backup)

• Supports the 5140DLM optional backup dialer for the second phone line.

• Supports ADEMCO Contact ID; ADEMCO High Speed; ADEMCO Express; and 3+1, 4+1, and 4+2 ADEMCO and

Sescoa/Radionics Low-Speed formats.

The system is shipped defaulted for Contact ID communication. It is the only format capable of uniquely reporting all

250 zones, as well as openings and closings for all 250 users. This requires central stations to be equipped with the

MX8000 receiver to fully support all new VISTA-128FBP/VISTA-250FBP report codes. If you need to update your

MX8000 receiver, contact your distributor.

• Provides the Dialer Queue Report in the event of a loss of communications between the dialer and the central

station, i.e. telco loss. The total events that will be queued up are 128 (91 Burg + 37 Life Safety). A Dialer Queue

Overflow report (E354) will be sent if the report queue goes beyond its limits. Note that: Life Safety includes Fire,

CO, 24 HR Silent/Audible/Auxiliary, and Duress. Life Safety events may go beyond 37 (up to 128) if there are no

Burg events in the queue. If all dialer attempts are exhausted before communication to the central station is

restored, the queue will be cleared.

Downloading

• Supports upload and download capability. (Downloading must be site-initiated for Commercial Fire installations.)

• Can perform unattended downloading (no one at the downloading computer).

• Provides an Installer Unattended Program Mode. This allows the installer to program the download phone number,

subscriber number, and primary central station receiver phone number without entering the normal program mode.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 135 136

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-250FBP Guia de preparacion Pagina 16

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-250FBP