ADEMCO VISTA-250FBP Guia de preparacion descargar pdf (Pagina 68)

VISTA-128FBP/VISTA-250FBP Installation and Setup Guide

5-4

FIELD TITLE and DATA ENTRIES EXPLANATION

*33

Primary Phone Number

Enter 0-9; #11 for *, #12 for #, #13 for a 2-

second pause.

Enter the primary central station phone number, up to 17 digits. This is the

phone number the control will use to transmit Alarm and status messages to

the central station. Do not fill unused spaces.

NOTE: Backup reporting is automatic only if a secondary phone number is

entered.

*34

Secondary Phone Number

Enter 0-9; #11 for *, #12 for #, #13 for a 2-

second pause.

Enter the secondary phone number, up to 17 digits. The secondary phone

number is used if communication on the primary number is unsuccessful, or if

split/dual reporting is desired. Do not fill unused spaces.

NOTE: If this field is programmed, a secondary subscriber account number

(field *90)

must

also be programmed.

*35

Download Phone Number

Enter 0-9; #11 for *, #12 for #, #13 for a 2-

second pause.

Enter the downloading phone number, up to 17 digits. Do not fill unused

spaces.

NOTE: This field is applicable only if downloading is utilized.

*36

Download ID Number

Make entries as 2-digit numbers as follows:

00=0 01=1 02=2 03=3 04=4 05=5

06=6 07=7 08=8 09=9 10=A 11=B

12=C 13=D 14=E 15=F

Enter eight digits.

NOTE: This field is applicable only if downloading is utilized.

*37

Download Command Enables

0 = disable

1 = enable

Enabling a function means that you are able to perform that function via the

ADEMCO Compass Downloading software.

Functions are as follows: Dialer Shutdown; System Shutdown; Not Used;

Remote Bypass; Remote Disarm; Remote Arm; Upload Program; Download

Program.

For Commercial Burglary and Fire installations, all entries must be 0.

*38

Prevent Zone XXX Bypass

(partition-specific)

Enter a zone number (001-250).

Enter 000 if all zones can be bypassed.

Enter three digits for zone that cannot be bypassed by the user.

NOTES:

The actions manual bypass, group bypass, auto-stay, and STAY/INSTANT

arming modes cannot bypass any zone programmed in this field.

The system will not arm if the zone is programmed with the vent zone or force

arm fault attributes.

*39

Enable Open/Close Report for

Installer Code (partition-specific)

0 = disable

1 = enable

If enabled, whenever the Installer Code is used to arm or disarm the partition,

an open/close report is sent to the central station.

*40

Enable Open/Close report for

Keyswitch

0 = disable

1 = enable

If enabled, whenever the keyswitch is used to arm or disarm the partition, an

open/close report is sent to the central station.

*41

Normally Closed or EOLR (Zones

3-8)

0 = EOLR supervision

1 = N.C. loops

If EOLR supervision is selected, end-of-line resistors must be used on zones

3-8.

If N.C. loops is selected, end-of-line resistors cannot be used and only

normally closed devices must be used.

Must be set to “0” for Commercial Fire and Burglary installations.

*42

Dial Tone Pause

Enter the wait time for dial tone detection:

0 = 5 seconds; 1 = 11 seconds; 2 = 30

seconds.

Enter the time the system waits for dial tone before dialing. Applies if true dial

tone is not selected in field *43.

Must be 0 for UL installations.

*43

Dial Tone Detection

0 = disable

1 = enable

If enabled, the system waits for true dial tone. If no dial tone is detected,

control dials at end of pause programmed in field *42.

If disabled, the system pauses for seconds entered in field *42, then dials.

NOTE: Disabling may be necessary in high-noise environment telco networks

where noise can be confused with dial tone, resulting in premature dialing.

1 2 ... 63 64 65 66 67 68 69 70 71 72 73 ... 135 136

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-250FBP Guia de preparacion Pagina 68

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-250FBP