ADEMCO VISTA-250FBP Guia de preparacion descargar pdf (Pagina 66)

VISTA-128FBP/VISTA-250FBP Installation and Setup Guide

5-2

FIELD TITLE and DATA ENTRIES EXPLANATION

*10

Exit Delay #1 (partition-specific)

Enter 03-15 multiplied by 15 seconds.

00 = no delay.

Exit delay defines the delay period that allows users to leave the premises

through a door that has been programmed as an entry/exit delay door after

arming the system without setting off the alarm.

NOTE: The delay must be set for a minimum 45 seconds for SIA installations.

*11

Entry Delay #2 (partition-specific)

Enter 02-15 multiplied by 15 seconds.

00 = no delay.

Entry Delay #2 is used for a secondary door requiring a longer delay than

those assigned to Entry Delay #1.

NOTE: The delay may not exceed 45 seconds for UL installations. The entry

delay time and Burg Alarm Comm Delay (field *88) combined cannot exceed 1

minute for SIA installations.

*12

Exit Delay #2 (partition-specific)

Enter 03-15 multiplied by 15 seconds.

00 = no delay.

Exit Delay #2 is used for a secondary door requiring a longer delay than those

assigned to Exit Delay #1.

NOTE: The delay may not exceed 60 seconds for UL installations. The delay

must be set for a minimum 45 seconds for SIA installations.

*13

Bell 1 Timeout

Enter 01-15 multiplied by 2 minutes.

00 = no timeout.

Defines the length of time the Bell 1 Output and the keypad’s sounder will

sound for all audible alarms.

Must be minimum 16 minutes for Commercial Burglary installations. Must be

minimum 6 minutes for Commercial Fire and SIA installations.

Trigger or RS232 Input

0 = trigger

1 = RS232 input

Select if J2 Pin 5 is being used as Fire Alarm trigger output or as an RS232

input. If set for RS232, this enables the system to receive serial data (75

baud).

NOTE: Must be set to “0” for Commercial Fire installations.

*14

*15

Keyswitch Assignment

Enter 1-8 partition keyswitch is being used.

Enter 9 if the keyswitch is being used to

silence fire Notification Appliance Circuits in

the event of a fire alarm.

Enter 0 if the keyswitch is not used.

The keyswitch requires the use of zone 7 wired loop (zone 7 is no longer

available as protection zone). The fire and panic alarm voltage triggers (J2)

automatically become ARMING and READY status outputs for the Keyswitch

LEDs.

Openings/closing report as user “0” if enabled in field *40.

*16

Bell 1 Confirmation of Arming

Ding (partition-specific)

0 = disable

1 = enable

If enabled, produces ½-second external alarm sounding (“ding”) at the end of

exit delay (or after kissoff from the central station, if sending closing reports).

NOTE: If using a keyfob, when the button is pressed, either for arming or

disarming, the bell will ding indicating that the button is working.

Must be 1 for UL commercial burglary installations.

*17

AC Loss Keypad Sounding

0 = disable

1 = enable

If enabled, sounding at the keypad (rapid beeping) occurs when AC power is

lost (sounding occurs about 2 minutes after actual AC loss).

Must be 1 for Commercial Fire installations.

*19

Randomize AC Loss Report

0 = within 2 minutes

1 = 10-40 minutes

2 = 1-3 hours

3 = 6-12 hours without Type 13, 1-3 hours

with Type 13

If enabled, randomizes AC loss reporting within the selected time after an

actual AC loss.

If disabled (0), AC loss reporting about 2 minutes after actual AC loss.

Selecting this option helps prevent an overload of AC loss messages at the

central station during a community blackout.

Must be 2 for Commercial Fire installations.

*20

VIP Module Phone Code

1-9 = first digit of access code

∗

∗∗

∗ or # = second digit of access code (enter #

+11 for “∗”, or # +12 for “#”)

To disable enter 00 for the 1

digit

If a 4286 Voice Module is being used, enter the 2-digit phone code used to

access the system.

Must be set to “00” for Commercial Fire and Commercial Burglary

installations.

*22

Keypad Panic Enables (partition-

specific)

0 = disable

1 = enable

If enabled, the keypad panics (zones 995, 996, and 999) may be used in this

partition. There are three entries in this field, one for each panic.

Use for Burglary panic types only.

Do not use on partition 1 on fire systems.

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 135 136

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-250FBP Guia de preparacion Pagina 66

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-250FBP