ADEMCO VISTA-250FBP Guia de preparacion descargar pdf (Pagina 69)

Section 5 – Data Field Descriptions

5-5

FIELD TITLE and DATA ENTRIES EXPLANATION

*44

Ring Detection Count

Enter 00 to disable ring detection.

Enter 01-14 for ring counts of 1-14.

Enter 15 to select Answering Machine Defeat

Mode

NOTES:

In the Answering Machine Mode, the caller should let the phone ring once,

then hang up, and call again within 30 seconds. The system, upon hearing

one ring followed by nothing, does not answer the first call, but readies itself to

pick up on the first ring of the next incoming call that is received within 30

seconds (i.e., the downloader calling again).

Must be set to “00” for Commercial Fire and Burglary installations.

*45

Primary Format

0=Low Speed; 1=Contact ID; 2=ADEMCO

High Speed; 3=ADEMCO Express

Enter the reporting format for the primary telephone number.

*46

Low Speed Format (Primary)

0 = ADEMCO Low Speed

1 = Sescoa/Radionics

Enter the low speed format for the primary telephone number.

*47

Secondary Format

0=Low Speed; 1=Contact ID; 2=ADEMCO

High Speed; 3=ADEMCO Express

Enter the reporting format for the secondary telephone number.

*48

Low Speed Format (Secondary)

0 = ADEMCO Low Speed

1 = Sescoa/Radionics

Enter the low speed format for the secondary telephone number.

*49

Checksum Verification

Enter 2 digits, one for the primary and one

for the secondary.

0 = disable

1 = enable

If enabled, the system for either or both primary/secondary formats sends a

verification digit to validate the message at the receiver without having to send

two message rounds. Selection is valid for 3+1, 4+1, and 4+2 reports.

*50

Sescoa/Radionics Select

0 = disable

1 = enable

If disabled, selects Radionics, which uses hexadecimal 0-9, B-F reporting.

If enabled, selects Sescoa, which uses only numeric reporting (0-9).

NOTE: The selection applies to both primary and secondary phone numbers.

*51

Dual Reporting

0 = disable

1 = enable

If enabled, all reports are to be sent to both primary and secondary phone

numbers.

NOTE: If used with Spilt Reporting "1" option (1*34), alarms and alarm

restores go to both primary and secondary numbers, while all other reports go

to secondary only. If used with Split Reporting "2" option, alarms and alarm

restores go to both, open/close and test messages go to secondary only,

while all other reports go to primary. If used with Split Reporting “3” option, fire

alarms and fire restore signals go to both, all other reports go to secondary

only.

NOTE: For Remote Station Applications, where separate transmission circuits

are required for Fire, Supervisory (when applicable), and Trouble signals,

option 3 must be enabled.

*52

Standard/Expanded Reporting

Primary

0 = disable

1 = enable

This field has six entries as follows: Alarm, Restore, Bypass, Trouble,

Open/Close, Low Battery. If enabled, expanded reports are sent to the

primary phone number if low speed format is selected in field *45.

NOTE: Expanded overrides 4+2 format.

*53

Standard/Expanded Reporting

Secondary

0 = disable

1 = enable

This field has six entries as follows: Alarm, Restore, Bypass, Trouble,

Open/Close, Low Battery. If enabled, expanded reports are sent to the

secondary phone number if low speed format is selected in field *47.

NOTE: Expanded overrides 4+2 format.

1 2 ... 64 65 66 67 68 69 70 71 72 73 74 ... 135 136

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-250FBP Guia de preparacion Pagina 69

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-250FBP