ADEMCO VISTA-250FBP Guia de preparacion descargar pdf (Pagina 44)

VISTA-128FBP/VISTA-250FBP Installation and Setup Guide

3-22

Installing Output Devices

The VISTA-128FBP/VISTA-250FBP supports up to 96 outputs. Each device must be programmed as to how to act

(ACTION), when to activate (START), and when to deactivate (STOP). The 4204, 4204CF, and/or 4101SN may be used

as output devices.

NOTE: The first 32 of the 96 Output Devices may be supervised (zones 601-632). Only the relays on 4204CF

module may be supervised. If supervision is programmed for other types of Output Devices, unpredictable

results may occur.

Installing the 4204 (Burg only) and 4204CF Relay Modules

Each 4204 module provides 4 relays with Form C (normally open and normally closed) contacts. Each 4204CF module

adds one style-Y supervised Notification Appliance Circuit to the system. For 4204CF modules, only relays 1 or 3 on

each module can be programmed.

The relay module will not operate until the device address you have set the DIP switches for is enabled in the

control’s

Device Programming

in the

#93 Menu Mode

• Relays should not re-energize until the panel is fully reset.

• For Commercial Fire installations, only one notification appliance module may be used, and only one

notification appliance output (A or B) may be used on that module.

• If the 4204CF relay is enabled for a NAC, it must follow the action of the NAC on the panel.

• Relays (aux and 4204's) cannot be used for off-premises signaling

• In Commercial Fire installations, the 4204CF cannot be used to drive sounders in the same physical area as

sounders connected to the alarm outputs of the control panel.

• Output devices are not intended for overriding automatic building and fire functions.

To install the relay modules, see Figures 3-20 and 3-21 and perform the following steps:

Step Action

1 Set the 4204 or 4204CF’s DIP switches for a device address 01-15.

Do not use an address being used by another device (keypads, RF receivers, etc.).

2 Mount the 4204 and 4204CF modules per the instructions provided with them.

Connect the module’s wire harness to the control (11, 12, 13 and 14). Plug the connector on the harness to

the module.

When mounting remotely, homerun each module to the control. The table below shows the maximum wire

run lengths. Refer to the instructions provided with the 4204CF for its maximum permissible wire lengths.

Wire Gauge Maximum Length

#22 125 feet

#20 200 feet

#18 300 feet

#16 500 feet

4204 ADDRESS SETTINGSSWITCH

NUMBER

("—" means "OFF")

1 2 3 4 5 6 7 8 9 101112131415

ON — ON — ON — ON — ON — ON — ON — ON —

ON ON ——ON ON ——ON ON ——ON ON ——

ON ON ON ON ————ON ON ON ON ————

ON ON ON ON ON ON ON ON ————————

12345

➞

OFF ON

TB1

4204

TB2

4-PIN

CONSOLE

PLUG

RELAY

TYPICAL

(SHOWN "OFF")

EITHER OR BOTH

CAN BE USED

DATA IN FROM

CONTROL

(–) GROUND

DATA OUT

TO CONTROL

(+) 12V

YEL

BLK

GRN

RED

SWITCH SHOWN

FOR ADDRESS "0"

DIP SWITCH FOR

SETTING DEVICE

ADDRESS AND

ENABLING/DISABLING

TAMPER

COVER

TAMPER

(REED)

SWITCH

13 14 15 16

4204-01-V1

NOT USED

Figure 3-20: 4204 Relay Module

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 135 136

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-250FBP Guia de preparacion Pagina 44

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-250FBP