ADEMCO VISTA-250FBP Guia de preparacion Pagina 60
- Pagina / 136
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
VISTA-128FBP/VISTA-250FBP Installation and Setup Guide
4-6
Communication Defaults for Zones (continued)
ZONE # 1st 2nd ZONE # 1st 2nd ZONE # 1st 2nd ZONE # 1st 2nd
213
03 00
227
02 00
240
15 00
970
00 00
214
04 00
228
03 00
241
01 00
988
00 00
215
05 00
229
04 00
242
02 00
990
00 00
216
06 00
230
05 00
243
03 00
992
(DURESS)
11 00
217
07 00
231
06 00
244
04 00
995
01 00
218
08 00
232
07 00
245
05 00
996
02 00
219
09 00
233
08 00
246
06 00
997
06 00
220
10 00
234
09 00
247
07 00
999
03 00
221
11 00
235
10 00
248
08 00
ALARM
RST.
01 00
222
12 00
236
11 00
249
09 00
TROUBLE
01 00
223
13 00
237
12 00
250
10 00
TRBLE.
RST
01 00
224
14 00
238
13 00
601-632
00 00
BYPASS
01 00
225
15 00
239
14 00
800-830
00 00
BYP. RST.
01 00
226
01 00
Zone Response Type Definitions
Each zone must be assigned a zone type, which defines
the way in which the system responds to faults in that
zone. There are three keypad-activated zones (panic
keys; see note) for each partition, a polling loop
supervision zone, and four RF supervisory zones, two
for each RF receiver installed. Zone types are defined
below.
Type 00: Zone Not Used
Program with this zone type if the zone is not used.
Type 01: Entry/Exit #1 Burglary
Provides entry delay whenever the zone is faulted and
the system is armed in the AWAY or STAY mode. When
the panel is armed in the INSTANT or MAXIMUM
mode, no entry delay is provided. Exit delay begins
whenever the control is armed, regardless of the arming
mode selected. These delays are programmable.
Assign this zone type to zones that are used for primary
entry to and exit from the facility.
Type 02: Entry/Exit #2 Burglary
Provides a secondary entry delay, if the system is
armed in the AWAY or STAY modes and the zone is
faulted. When the panel is armed in the INSTANT or
MAXIMUM mode, no entry delay is provided.
Secondary exit delay begins whenever the control is
armed, regardless of the arming mode selected. These
delays are programmable.
Assign this zone type to zones that are used for entry
and exit of the facility and require more time than the
primary entry and exit point. Delay times for this zone
type must be greater than those for zone type 01 (e.g., a
garage, loading dock, or basement door).
Type 03: Perimeter Burglary
Provides an instant alarm if the zone is faulted and the
system is armed in the AWAY, STAY, INSTANT, or
MAXIMUM mode.
Assign this zone type to all exterior doors and windows.
Type 04: Interior, Follower
Provides a delayed alarm (using the programmed entry
delay time) if an entry/exit zone is faulted first.
Otherwise it produces an instant alarm. It is active
when the system is armed in the AWAY or MAXIMUM
mode, but the MAXIMUM mode eliminates the entry
delay.
If the Interior Follower zone is programmed for one of
the STAY modes (default is STAY mode 1), it is
automatically bypassed when the panel is armed in the
STAY or INSTANT mode.
Assign this zone type to a zone covering an area such as
a foyer, lobby, or hallway through which one must pass
upon entry or exit (to and from the keypad).
Type 05: Trouble by Day/Alarm by Night
Provides an instant alarm if the zone is faulted and the
system is armed in the AWAY, STAY, INSTANT, or
MAXIMUM mode. During the disarmed state (day), the
system annunciates a latched trouble sounding from
the keypad (and a central station report, if desired).
Assign this zone type to a zone that contains a foil-
protected door or window (such as in a store), or to a
zone covering a sensitive area such as a stock room or
drug supply room. It can also be used on a zone in an
area where immediate notification of an entry is
desired.
Type 06: 24-Hour Silent Alarm
Sends a report to the central station but provides no
keypad display or sounding. Assign this zone type to a
zone containing an Emergency button.
Type 07: 24-Hour Audible Alarm
Sends a report to the central station and provides an
alarm sound at the keypad and an audible external
alarm. Assign this zone type to a zone containing an
Emergency button.
Type 08: 24-Hour Auxiliary Alarm
Sends a report to central station and provides an alarm
sound at the keypad only. (No other Notification
Appliance Circuit is activated.) Assign this zone
type to a zone an Emergency button or one containing
monitoring devices such as water sensors or
temperature sensors.
- K0376V2 7/09 Rev. B 1
- Table of Contents 3
- List of Figures 6
- PRODUCT MODEL NUMBERS: 7
- General Requirements 9
- COMMUNICATIONS 12
- General Description 15
- YELLOW DATA 18
- GREEN DATA 18
- Partitioning 19
- COMMON LOBBY 20
- Installing the Control 23
- Commercial Fire Guidelines 24
- Installing the Keypads 25
- Device Programming 26
- #93 Menu 26
- Auxiliary Relay Connections 30
- Telephone Line Connections 31
- Main Dialer Connections 31
- 2000 OHMS 34
- Figure 3-11 35
- Zone Programming 37
- VPLEX-VSI 39
- Wireless Zone Expansion 40
- Programming 41
- #93 Menu Mode 41
- 5881-001-V0 42
- SWITCH (N.O.) 46
- Event Log Connections 48
- Connecting the Transformer 48
- Earth Ground Connections 49
- Battery 52
- BATTERY TABS 53
- MAIN PCB 53
- #93 Menu Mode Programming 56
- Section 4 – Programming 57
- MAIN MENU 57
- OPTIONS 57
- Zone Number Designations 58
- Polling Loop Supervision 61
- SECTION 3: 61
- Zone Input Type Definitions 62
- Programming for Communicator 63
- Programming Guide 65
- Report Code Programming 67
- Output Programming 75
- ✳16 for Waterflow and 78
- Scheduling Options 81
- Time Window Definitions 82
- Limitation of 85
- Access Schedules Programming 85
- #80 Scheduling Menu Mode 85
- Daily Open/Close Schedules 86
- Holiday Schedules 86
- Time-Driven Events 87
- 30=Auto bypass – Zone list 90
- 31=Auto unbypass – Zone list 90
- 42=Enable Access Window for 90
- Access group(s) 90
- 50=Off-Normal Reminder 90
- 1 91
- 2 91
- 3…8 91
- Temporary Schedules 92
- User Scheduling Menu Mode 94
- Downloading Primer 95
- Section 7 – Downloading 97
- Figure 7-1 98
- Setting the Real-Time Clock 99
- User Access Codes 101
- User 3 User 3 102
- Level 1 Level 4 102
- Master Oper B 102
- EXPLANATION 103
- Exiting the User Edit Mode 104
- Testing the System 105
- Burglary Walk-Test ( 106
- Armed Burglary System Test 107
- Trouble Conditions 108
- To the Installer 109
- Regulatory Agency Statements 111
- FCC PART 68 NOTICE 113
- Summary of System Commands 115
- Specifications 117
- Contact ID Codes 119
- Event Log Alpha Descriptors 120
- 4-3, 4-4 124
- 6-4, 6-2 125
- 6-4, 6-5 127
- WARNING: 135
- ÊK0376V2Š 136
- ÊK0376V2ŠÊK0376V2Š 136
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-250FBP
Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15CN Manual de usuario
(16 paginas)
(16 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO Ademco VISTA-40 Manual de usuario
(110 paginas)
(110 paginas)
(64 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.187 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales