ADEMCO VISTA-250FBP Guia de preparacion descargar pdf (Pagina 71)

Section 5 – Data Field Descriptions

5-7

FIELD TITLE and DATA ENTRIES EXPLANATION

*83

First Test Report Time

Enter 00-07the for day (01 = Monday)

Enter 00-23 for the hour

Enter 00-59 for the minutes

Enter the day and time that the first Test report shall be transmitted. Enter 00

in all locations if the Test report is to be sent immediately upon exiting. Enter

00 in the day location if the report is to be sent at the next occurrence of the

time that is set.

*84

Swinger Suppression (partition-

specific)

Enter 01-15.

Enter 00 for unlimited reports

This option limits the number of messages (alarms or troubles) sent for a

specific zone in an armed period.

Must be set to “00“ for Commercial Fire and Burglary installations.

*85

Enable Dialer Reports for Panics

& Duress (partition-specific)

0 = disable

1 = enable

This field has four entries as follows: Zone 995, 996, 999, Duress Enable for

each partition that the panics and duress reporting is desired.

NOTE: Non-zero report code must be assigned to zone 992 (duress) to

enable Duress reporting.

*87

Entry Warning (partition-specific)

0 = 3 short beeps

1 = slow continuous beeps

Select the type of warning for the entry delay period.

*88

Burglary Alarm Communicator

Delay (partition-specific)

0 = no delay

1 = 30-second delay

Select the delay, if any, for burglary alarm communications.

Must be 0 for UL installations.

Must be 1 for SIA installations.

*89

Alarm Restore Report Timing

0 = Restore is sent when zone is restored or

at disarming, whichever occurs first.

1 = Restore is sent at disarming whether

zone is restored or not, or at bell timeout, but

only if restored.

2 = Restore is sent at disarming, whether the

zone is restored or not.

Select the time when restore reports are sent after an alarm.

This field applies only to Burglary zone types. It does not apply to Fire or

Panic zone types.

Must be set to “2” for Commercial Burglary installations.

*90

Secondary Subscriber Account

Number (partition-specific)

Enter 00-09; B-F (11-15)

Enter a 3- or 4-digit (depending on report format) primary subscriber account

number. Each number requires a 2-digit entry so as to allow entry of

hexadecimal digits (B-F). If a 3-digit account number is to be used, enter data

only in the first three locations, and enter * in the fourth location.

NOTE: This field

must

be programmed if a secondary phone number is used

(field *34). This account number can be the same as the primary account

number.

1*11

Zone Bypass After Disarm

0 = disable

1 = enable

Enter 1 for each partition in which zones will remain bypassed after disarm.

NOTES:

For each partition in which field 1✳11 is enabled, the USER CODE + OFF will

no longer unbypass zones. To unbypass ALL zones, you must enter USER

CODE + # + 64. To unbypass zones INDIVIDUALLY, you must enter USER

CODE + 6 + zone number.

Any zone that was automatically bypassed by the system will be unbypassed

upon disarming of the system (e.g., STAY mode, Auto-STAY, etc.).

Vent zones and zones bypassed by a programmed Auto-Bypass schedule

(Timed Driven Event) are considered “manual bypasses” and will not be

unbypassed upon disarming the system.

Zones that were in a bypassed state at the time a System Shutdown is sent

from the Compass Downloading software will be unbypassed when the

System Shutdown is removed.

1*12

Program Notification Signal

0 = no

1 = yes

If enabled, sends signal to central station indicating the system has been put

in programming mode.

Must be 1 for Commercial Fire installations.

1 2 ... 66 67 68 69 70 71 72 73 74 75 76 ... 135 136

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-250FBP Guia de preparacion Pagina 71

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-250FBP