ADEMCO VISTA-250FBP Guia de preparacion Pagina 51
- Pagina / 136
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Section 3 - Installing the Control
3-29
3. In Worksheet 3, enter devices used on
Auxiliary Power 2. Calculate standby and
alarm currents, then add to get Auxiliary
Power 2 current subtotal.
Worksheet 3: Auxiliary Power 2 Current Load
Total Current
Device
Model #
Device Current X
# of Units
Standby Alarm
Auxiliary Power 2 Subtotal
(pin 5 on keypad port 2)
400mA max.
1.7A max.
4. In Worksheet 4, enter devices connected to the
Bell 1 Output. Calculate alarm currents, then
add to get the Bell 1 Output current subtotal.
Worksheet 4: Bell 1 Output Current Load
Total Current
Device
Model #
Device Current X
# of Units
Standby Alarm
XXXXXX
XXXXXX
XXXXXX
XXXXXX
XXXXXX
XXXXXX
XXXXXX
Bell 1 Output Subtotal
(terminals 3 & 4 – 1.7A max.)
5. In Worksheet 5, enter devices connected to the
Bell 2 Output. Calculate alarm currents, then
add to get the Bell 2 Output current subtotal.
Worksheet 5: Bell 2 Output Current Load
Total Current
Device
Model #
Device Current X
# of Units
Standby Alarm
XXXXXX
XXXXXX
XXXXXX
XXXXXX
XXXXXX
XXXXXX
Bell 2 Output Subtotal
(terminals 5 & 6 – 1.7A max.)
6. In Worksheet 6, enter the total calculated subtotals
of all listed outputs from Worksheets 1 through 5, then
add to get the combined current.
Worksheet 6: Total VISTA-128FBP/VISTA-250FBP
Current Load
Total Current
Standby Alarm
Polling Loop Subtotal
Auxiliary Power 1 Subtotal
Auxiliary Power 2 Subtotal
Bell 1 Output Subtotal
Bell 2 Output Subtotal
VISTA-128FBP/VISTA-250FBP
PCB Current (Incl. 2-wire smoke
detector loading on zones 1 & 2)
300mA 470mA
5140DLM Backup Dialer Module
5mA
(inactive)
15mA
(active)
Total Current Load
(1A max. standby; 2.3A max. alarm)
NOTE: The 5140DLM actually draws 55mA when active.
However, since the control panel PCB current includes the
main dialer current, and since the main dialer is inactive when
the 5140DLM is active, the 5140DLM imposes only a 15mA
added load on the current supply.
- K0376V2 7/09 Rev. B 1
- Table of Contents 3
- List of Figures 6
- PRODUCT MODEL NUMBERS: 7
- General Requirements 9
- COMMUNICATIONS 12
- General Description 15
- YELLOW DATA 18
- GREEN DATA 18
- Partitioning 19
- COMMON LOBBY 20
- Installing the Control 23
- Commercial Fire Guidelines 24
- Installing the Keypads 25
- Device Programming 26
- #93 Menu 26
- Auxiliary Relay Connections 30
- Telephone Line Connections 31
- Main Dialer Connections 31
- 2000 OHMS 34
- Figure 3-11 35
- Zone Programming 37
- VPLEX-VSI 39
- Wireless Zone Expansion 40
- Programming 41
- #93 Menu Mode 41
- 5881-001-V0 42
- SWITCH (N.O.) 46
- Event Log Connections 48
- Connecting the Transformer 48
- Earth Ground Connections 49
- Battery 52
- BATTERY TABS 53
- MAIN PCB 53
- #93 Menu Mode Programming 56
- Section 4 – Programming 57
- MAIN MENU 57
- OPTIONS 57
- Zone Number Designations 58
- Polling Loop Supervision 61
- SECTION 3: 61
- Zone Input Type Definitions 62
- Programming for Communicator 63
- Programming Guide 65
- Report Code Programming 67
- Output Programming 75
- ✳16 for Waterflow and 78
- Scheduling Options 81
- Time Window Definitions 82
- Limitation of 85
- Access Schedules Programming 85
- #80 Scheduling Menu Mode 85
- Daily Open/Close Schedules 86
- Holiday Schedules 86
- Time-Driven Events 87
- 30=Auto bypass – Zone list 90
- 31=Auto unbypass – Zone list 90
- 42=Enable Access Window for 90
- Access group(s) 90
- 50=Off-Normal Reminder 90
- 1 91
- 2 91
- 3…8 91
- Temporary Schedules 92
- User Scheduling Menu Mode 94
- Downloading Primer 95
- Section 7 – Downloading 97
- Figure 7-1 98
- Setting the Real-Time Clock 99
- User Access Codes 101
- User 3 User 3 102
- Level 1 Level 4 102
- Master Oper B 102
- EXPLANATION 103
- Exiting the User Edit Mode 104
- Testing the System 105
- Burglary Walk-Test ( 106
- Armed Burglary System Test 107
- Trouble Conditions 108
- To the Installer 109
- Regulatory Agency Statements 111
- FCC PART 68 NOTICE 113
- Summary of System Commands 115
- Specifications 117
- Contact ID Codes 119
- Event Log Alpha Descriptors 120
- 4-3, 4-4 124
- 6-4, 6-2 125
- 6-4, 6-5 127
- WARNING: 135
- ÊK0376V2Š 136
- ÊK0376V2ŠÊK0376V2Š 136
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-250FBP
Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15CN Manual de usuario
(16 paginas)
(16 paginas)
Los Sistemas De Control De Acceso De Seguridad ADEMCO Ademco VISTA-40 Manual de usuario
(110 paginas)
(110 paginas)
(64 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.110 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales