ADEMCO 4140XMPT2 Manual de usuario descargar pdf (Pagina 62)

– 62 –

Partition-Specific Field

Descriptions

(continued)

* 2 2 Console Panic Enables

Enter 1 to enable the appropriate console panics used in this partition.

Otherwise enter 0.

* 2 3 Multiple Alarms

Determines whether or not more than one alarm can be sounded in a given

zone during an armed period. Note that multiple alarm soundings will not

occur more frequently than allowed by the programmed alarm sounder

duration. This selection applies to local sounding and has no impact on the

number of communication messages transmitted. Refer to Swinger

Suppression for limiting communication messages. Enter 1 if this feature is

desired. Enter 0 if not desired.

*29 Quick Arm

Enter 1 to enable arming of the burglary system in AWAY, STAY, INSTANT

or MAXIMUM modes by using the # key instead of the security code. When

armed, reports closing as User 0 if open/close reporting for User #2

(typically a master level user) was enabled for a given partition. Enter 0 if

Quick Arm is not desired. (The security code must always be used to disarm

the system.) Note that if quick arm is used, the installer code and authority

level 5 code cannot disarm the system.

* 3 2 Primary Subscriber Acct #

Enter a 3 or 4 digit (depending on report format) primary subscriber account

number 00-09; B-F (11-15). Each number requires a 2-digit entry so as to

allow entry of hexadecimal digits (B-F). If a 3 digit account number is to be

used, only enter data in the first 3 locations, leaving the last one unfilled, by

entering a *.

* 3 8 Inhibit Bypass Of A Zone

Entering a zone number (01-87) prevents that zone from being bypassed

by the user. Enter 00 if this feature is not desired (all zones can be

bypassed). This selection does not affect fire zones, which the system

prevents from being bypassed.

* 3 9 Enable Open/Close Report For Installer Code

Enter 1 if open/close reporting for the installer is desired. Otherwise enter 0.

* 8 4 Intermittent Sensor Suppression

This option limits the number of messages (Alarms or Troubles) sent for a

specific channel in an armed period (Intermittent Sensor Suppression). Enter

01-15. If 00 is selected, all Alarm or Trouble codes are reported.

* 8 5 Enable Dialer Reports For Panics & Duress

Enter 1 for each panic/duress for which reporting is desired.

*87 Entry Warning

Enter 0 for 3 short beeps, or 1 for slow beeps that continue for the entire

entry delay period.

* 8 8 Burg. Alarm Comm. Delay

Enter 0 for no delay on burglary alarm communication, or 1 for 16-second

delay (no delay on 24-hour reports).

* 9 0 Secondary Subscriber Acct #

Enter the 3 or 4 digit number (depending on report format) for the

secondary subscriber account, 00-09; B-F (11-15). Each number requires a

2-digit entry so as to allow entry of hexadecimal digits (B-F). If a 3-digit

number is to be used, only enter data in the first 6 locations, leaving the last

two unfilled. Default=15 15 15 15. Erase the field by entering *90*. NOTE:

This field must be programmed if a secondary phone number is used (field

*34). This account number can be the same as the primary account

number.

1 2 ... 57 58 59 60 61 62 63 64 65 66 67 ... 131 132

Comentarios a estos manuales

Sin comentarios

ADEMCO 4140XMPT2 Manual de usuario Pagina 62

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4140XMPT2