ADEMCO 4140XMPT2 Manual de usuario descargar pdf (Pagina 54)

– 54 –

DATA FIELD DESCRIPTIONS

Refer to the programming

form provided at the center

of this manual while

reviewing the following

programming sections.

The following section arranges the global (system wide) program fields into the

following functional groups: • Control Options • Wireless Options

• Downloading Options • Partitioning Options

• Dialer Options • Event Logging Options

Note that zone response types can be programmed in fields *02-*05 & 1*01-1*09,

but it is recommended that they be programmed via the #93 Menu Mode. For this

reason, these fields are not discussed in this section.

Control Options *00 Installer Code

4-digit code reserved for installation company use, but can be used by the

customer if needed. This is the only code that can be used to enter the

Program mode from the console. This code cannot be used to disarm the

system if not used to arm, or if Quick Arm was used to arm system. This

code cannot reenter programming mode if exited by the *98 command.

* 1 4 Zone 9 Fast/Slow Response

Enter 1 to set fast response mode (10msec) for appropriate devices wired

to zone 9. Enter 0 for normal response, 350msec. Must be 0 for UL.

* 1 5 Keyswitch Assignment

Enter the partition number 1-8 in which the keyswitch is being used;

otherwise, enter 0. Requires the use of zone 7 wired loop (zone 7 no

longer available as protection zone when used for keyswitch operation). If

the keyswitch is used, the fire and panic alarm voltage triggers automatically

become ARMING and READY status outputs for support of the Keyswitch

LEDs. NOTE: Zone type 10 is automatically assigned to zone 7 if a

keyswitch is used. Reports openings/closing by user "0" if reporting is

enabled in field *40.

* 1 7 AC Power Loss Console Sounding

Entering 1 enables sounding at the console (rapid beeping) when AC power

is lost is desired. Enter 0 if no AC power loss console sounding is desired.

* 1 8 AC Power Loss External Alarm

Entering 1 enables the external alarm sound after AC power has been out

for 4 hours; otherwise enter 0 (no alarm).

* 1 9 Randomize AC Loss Report

Enter 1 to randomize AC loss reporting between 10-40 min. after an actual

AC loss. Enter 0 for normal AC loss reporting (about 2 minutes after actual

AC loss). Selecting this option helps prevent an overload of AC loss

messages at the central station during a community blackout.

* 2 0 Phone Module Phone Access Code

If a 4285 Phone Module is being used, enter the 2-digit phone code used

to access the system. Enter 01-09 for the first digit, and enter 11 (for *) or

12 (for #) for second digit. To disable the phone module, enter 00 for the

first digit and enter 11 for the second digit of the code.

* 2 1 Disable Fire Time-Out

Enter 1 to disable (no timeout) the alarm sounder duration for any zone

designated as a fire zone, regardless of partition, so that fire sounding

continues until the system is reset. Enter 0 if the normal burglary alarm

sounder duration (partition-specific field *13) should apply to fire alarms.

* 2 4 Expansion Zone Tamper Disable

Only applicable if No. 4190WH RPMs are used on the polling loop or 5800

series transmitters are used. This option is used to disable this module's

tamper detection. Enter 1 to disable. Enter 0 if tamper detection is desired.

* 2 5 Burg. Trigger For Response Type 8

This field allows optional triggering of the voltage output on pin 7 of the J7

header for zone response type 8 (24hr. auxiliary). The 0 disable selection is

useful if J7 header pin 7 is used for a panic trigger, and non-panic devices

are used for all zones assigned to zone response type 8 (e.g. water sensor,

temp. sensor). If disabled, only burglary or audible panic alarms will trigger

pin 7. Otherwise, enter 1.

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 131 132

Comentarios a estos manuales

Sin comentarios

ADEMCO 4140XMPT2 Manual de usuario Pagina 54

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4140XMPT2