ADEMCO 4140XMPT2 Manual de usuario descargar pdf (Pagina 18)

– 18 –

Important! Fault

Annunciation

Since the polling loop and the RF receiver(s) are shared among the 8 partitions,

the scheme for annunciating their failure is as follows:

Respective faults (for zones 88-91 & 97) will report as trouble conditions only, and

as such, should be assigned either zone type 00 if no annunciation is desired, or

zone type 05 if annunciation as trouble condition is desired. If the polling loop or

RF link fails, the corresponding zone number will display a trouble condition for

each partition that uses the device that failed. In addition, all zones associated with

that device will indicate a fault condition. The trouble condition will not interfere

with the ability to arm the partition, but the faults must first be bypassed.

Compatible Polling Loop Devices

4208

Eight Zone Polling

Loop Expansion

Module

• Used to supervise up to 8 hard-wired devices via the polling loop. NOTE: Does

not support 2-wire smoke detectors.

• Set DIP switches to identify 8 zones.

• The first two zones can be either normal or fast response (DIP switch selectable).

• All zones are EOLR supervised (first six zones = 4.7k ohms, last two zones =

30k ohms), provided with the 4208.

4190WH

Two Zone Remote

Point Module

• Used to supervise 2 hard-wired devices via the polling loop.

• DIP switch programmable.

• The left zone can be EOLR supervised, if necessary, and can accept either

open or closed circuit sensors, and can be set for fast response. The right zone

is unsupervised and can accept closed circuit sensors only.

4278EX

Quad Element Polling

Loop PIR

• Quad element PIR with built-in RPM which is DIP switch programmable and

connects directly to the polling loop. Includes mirrors for both wide angle and

curtain/long range applications. Features an auxiliary sensor loop that permits

connection of another nearby closed circuit alarm sensor (reed contact, etc.).

4275EX

Dual Element Polling

Loop PIR

• Dual element PIR with built-in RPM which is DIP switch programmable. Includes

mirrors for both wide angle and curtain/long range applications and can use the

1875PA Pet Alley mirror. Built-in selectable pulse count capability.

4194

Surface Mounted Reed

Contact (Wide Gap)

• Wide gap surface mounted reed contact with built-in RPM, which is DIP switch

programmable.

4297

Polling Loop Extender

Module

• Can be used if the 2-wire polling loop must be greater than the recommended

length (4000' [1220m] max). By installing a 4297 at the end of the first loop, the

polling loop can be continued. If more than 64mA needs to be drawn from the

polling loop to power RPMs, use of the 4297 provides another loop with 128mA

available.

• Connects to the polling loop and is powered from auxiliary power.

4192SD

Photoelectric Polling

Loop Smoke

Detector

• One piece photoelectric smoke detector with built-in RPM which is DIP switch

programmable.

4192SDT

Photoelectric Polling

Loop Smoke Detector

w/Heat Detector

• One piece photoelectric smoke detector with 135°F (57°C) heat detector, and

built-in RPM which is DIP switch programmable.

4192CP

Ionization Smoke

Detector

• One piece products of combustion ionization detector with built-in RPM which is

DIP switch programmable.

4139SN

Auto Smart Surface

Mount Reed Contact

• Compact surface mount magnetic reed contact with built-in RPM.

• Serial number ID "learned" by control panel.

• Check product availability.

4191SN

Auto Smart Recessed

Reed Contact

• Recessed (1/2" [13mm] dia.) magnetic reed contact with built-in RPM.

• Serial number ID "learned" by control panel.

• Check product availability.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 131 132

Comentarios a estos manuales

Sin comentarios

ADEMCO 4140XMPT2 Manual de usuario Pagina 18

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4140XMPT2