ADEMCO 4140XMPT2 Manual de usuario descargar pdf (Pagina 52)

UsEn@Test Mod. After the installationis completed, the Security System should be thoroughly

testedon a partitionby partltlcnbasisas follows:

1, With the System in the disarmed state,

checkthat all zones are Intact, If *

DISARMED - Press [*] to show faults b displayed, press the ~] key to display

the descriptors of the faulted zone(s), Restore faulted zone(s) If necassary, so

that *“’DISARMEIY** READY TO ARM Is displayed,

2, Enter the security code and press the TEST key, The external sounder (If

used) should sound for 3 seconds

and then turn off (the system Is operating

on the back-up battery only at this time).

NOTE 1, If the sounder does not sound, this maybe an indication that the backup

battery Is discharged or missing.

NOTE 2, As a reminder that the system is kr the Test mode, the Console will

sound a single beep at 15-second intervals if no protection zones are violated.

NOTE 3, In the Test mode, no alarm reports will be sent to the central statbn,

Alec, the external sounder (if used) will not be activated,

Doors and Windows

Open and close each protected door

and window in turn. Each action should

produce three beeps

from the Console, The descriptor for each prctectbn zone

will appear on the Console display.

Motion Detectors

Walk in front of any interior motion detectors, Listen for three beeps

when the

detector senses movement. While it is activated, its descriptor will remain

displayed on the Console. Note that wireless PIRs will have a 3 minute lockout

between transmissionsto conserve battery life (remove cover for walk test to

overridethe 3-minute lock-out).

Smoke Detectors

Followthe test procedureprovidedby the manufacturerof each smoke detector _

to ensure that all detectors are operational and are functioning properly.

NOTE: A 2-wire smoke detector display will not clear until the Test mode is exited.

Turning Off TEST mode

Enter

the securitycode and pressthe OFF key.

Armed System Test

iMPORTANT! A message wili be sent to the centrai station during the foiiowing

tests.

Notify the centrai station that a test will be in progress.

NOTE: A display of “COMM. FAiLURE” indicates a failure to communicate (no

Kissoff by the receiver at the central station after the maximum number of

transmission attempts is tried). if this occurs, verify that the phone iine is

connected, the correct report format is programmed, etc.

Arm the system and fault one or more zones. Siience aiarm sounder(s) each

time by entering the code and pressing OFF.

Check that Entry/Exit deiay

zones

provide the assigned deiay times.

Check the keypad-initiated aiarms, if programmed

in fieid ’05, by pressing the

Panic key pairs (~] + [1], [#] + [3], ~]+ [#]). if the system has been programmed

for audibie emergency, the consoie wiil emit a ioud, steady aiarm sound. The

word

ALARM and a descriptor “99” wiii be displayed for ~] + [#]. (if ~] + [1] is

pressed, a “95”

wiil be dispiayed; if [#] + [3] is pressed, a “96 wiii be

displayed). Siience the aiarm by entering the security code and pressing OFF.

if the system has been programmed for siient panic, there wili be no audibie

aiarms or dispiays. A report will be sent to the centrai station, however.

Notify the central station that aii tests are finished and verify results with them.

-52-

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 67 68

Comentarios a estos manuales

Sin comentarios

ADEMCO 4140XMPT2 Manual de usuario Pagina 52

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4140XMPT2