ADEMCO 4140XMPT2 Manual de usuario descargar pdf (Pagina 16)

Important! Fault

Since the polling loop and the

RF receiver(s) are shared among the 8 partitions,

Annunciation

the scheme for annunciating their failure is as follows:

Respective faults (for zones 88-91 & 97) will report as trouble conditions only, and

as such, should be assigned either zone type 00 if no annunciation is desired, or

zone type 05 if annunciation as trouble condtiion is desired. If the polling loop or w

RF link fails, the corresponding zone number will display a trouble condition for

each partition that uses the device that failed. In additiin, all zones associated with

that device will indicate a fault condition. The trouble condition will not interfere

with the ability to arm the partition, but the faults must first be bypassed.

Compatible Poiiing Loop Devices

4208

Eight Zone Poiling

Loop Expansion

Module

4190WH

Two Zone Remote

Point Moduie

4278

Quad Element Poliing

LooP PIR

4275

Duai Eiement Polling

Loop PiR

4194

Surface Mounted Reed

Contact (Wide Gap)

4197

Polling Loop Extender

Moduie

4192SD

Photoelectric Poiling

Loop Smoke

Detector

4192SDT

Photoelectric Poiling

Loop Smoke Detector

w/Heat Detector

4192CP

ionization Smoke

Detector

4139SN

Auto Smart Surface

Mount Reed Contact

4191SN

Auto Smart Recessed

Reed Contact

“ Used to supervise up to 8 hard-wired devices via the polling loop. NOTE: Does

not support 2-wire smoke detectors.

● Set DIP switches to identify 8 zones.

● The first two zones can be either normal or fast response (DIP switch selectable).

● All zones are EOLR supervised (first six zones = 4.7k ohms, last two zones =

30k ohms), provided with the 4208.

● Used to supervise 2 hard-wired devices via the polling loop.

c DIP switch programmable.

● The left zone can be EOLR supervised, if necessary, and can accept either

open or closed circuit sensors, and can be set for fast response. The right zone

is unsupervised and can accept closed circuit sensors only.

s Quad element PIR with built-in RPM which is DIP switch programmable and

connects directly to the polling loop. Includes mirrors for both wide angle and

curtain/long range applications. Features an auxiliary sensor loop that permits

connection of another nearby closed circuit alarm sensor (reed contact, etc.).

c Dual element PIR with built-in RPM which is DIP switch programmable. Includes

mirrors for both

wide angle and curtain/long range applications and can use the

1875PA

Pet Alley mirror. Built-in selectable pulse count capability.

Wide gap surface mounted reed contact with built-in RPM, which is DIP switch ~

programmable.

● Can be used if the 2-wire polling loop must be greater than the recommended

length (4000’ max). By installing a 4197 at the end of the first loop, the polling

loop can be continued. If more than 64mA needs to be drawn from the polling

loop to power RPMs, use of the 4197 provides another loop with 64mA

available.

● Connects to the polling loop and is powered from auxiliary power or by a

separate 729 power supply with battery backup.

“ One piece photoelectric smoke detector with built-in RPM which is DIP switch

programmable.

● One piece photoelectric smoke detector with 1350F (57°C) heat detector, and

buitt-in RPM which is DIP switch programmable,

● One piece products of combustion ionization detector with built-in RPM which is

DIP switch programmable.

● Compact surface mount magnetic reed contact with built-in RPM.

● Serial number ID “learned” by control panel.

● Check product availability,

● Recessed (1/2” dia.) magnetic reed contact with built-in RPM.

● Serial number ID “learned” by control panel.

● Check product availability.

-16-

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 67 68

Comentarios a estos manuales

Sin comentarios

ADEMCO 4140XMPT2 Manual de usuario Pagina 16

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4140XMPT2