ADEMCO 4140XMPT2 Manual de usuario descargar pdf (Pagina 45)

EVENT LOGGING

Event Logging Printer Connector J8, located above connector J7 on the right side of the main PC

Connections

board, is intended to be interfaced to a local serial printer via the 41OOSMserial

interface module, in applications where it is desired to print the event log on a

local printer.

Mount the 41OOSMusing its clip bracket to attach it to the side wall of the control

cabinet. Make connections between J8, the 41OOSM module and the serial

printer as shown below. Refer to the event logging commands paragraph for a

description of the console commands which initiate event log printing.

NOTE 1: Printer must be configured as follows:

● 8 data bns, no parity, 1 stop bit

● 300 or 1200 baud (1200 preferred)

● Hardware handshaking using DTR signal

NOTE 2: The 41OOSMmodule is supplied with a 10 foot RS232 cable. A longer

cable or an extension cable can be used if the 4140XMPT2 and serial printer are

separated by more than 10 feet, but the total cable length should be less than 50

feet.

NOTE 3: Most printers either ignore the CTS, DSR and CD signals, or require

them to be high (i.e. 3-15VDC as measured on RS232 DB25 connector pins 5, 6

& 8 respectively with respect to ground pin 7). The 4100SM module sets these

pins high. If the printer being used will not operate with these pins high, then clip

the blue (CTS), white (DSR) or red (CD) jumpers on the

4100SM module to set

the corresponding signal floating. Impotlant pins on the RS232C cable are pin 3

(data out), pin 7 (ground) and pin

20 (DTR - ready).

NOTE 4: The DTR signal, as measured at 41OOSMTB1, should be high (9.5-

14VDC) when the printer is powered, properly connected, on-line and ready to

print. This signal will be low (O-1.5VDC) when the printer is not powered, not

properly connected, off-line or out of paper. The 4140XMPT2 will not send

printing data to the printer unless the DTR signal is high.

UL NOTE: A UL Listed EDP printer must be used for UL installations.

s CoNNEcmn

—

4142TR -E fswmlEO WI+ 41fts14

4tmm SEBIU

MciOu

1. 7s6 An Ran, (*]

(Z%71AOmaM &mv)

.FwR

To TB7 h. Pm {-) —

- mm)

6 mm

@ Ildund

@ uw.d

@ nul130d

@ Ildwed

I DTR

l!mshl wEW

(CUT 10 SET FIESPECWW S’,3MN FwATIW,

ddd

*D OWEWV

I I

USE GEWR

CWER suwum

Ion.

WTH 4,w5M F

CDW

FUIMTEl! HAS DE.% ~wm

MALECO.WECTOR

I {

SElnu PFWTER

mm D@ATAm’s

!83 Pm

Istwml

ZrKvmw

—~

(sM30m5muL

-45-

1 2 ... 40 41 42 43 44 45 46 47 48 49 50 ... 67 68

Comentarios a estos manuales

Sin comentarios

ADEMCO 4140XMPT2 Manual de usuario Pagina 45

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4140XMPT2