ADEMCO 4140XMPT2 Manual de usuario descargar pdf (Pagina 31)

Programming The

Consoies

Mounting The

Consoies

Wiring Consoies

Powering Additional

Consoies

The consoles can beset for an address of 0-30

iMPORTANT! You must select an address of O, 1, 2, or 3 if standard defaults

are to be programmed, since these are the only console addresses enabled by

the standard default. Refer to the addressable console DIP switch table at the

end of this manual to set the 4137AD and 5137AD address ID number. Refer to

the instructions provided with the 6139 to set its ID number.

Do not use address 31 with the 4140XMPT2. Address 31 causes the

console to operate in non-addressable mode (i.e. works like a standard, non-

addressable console).

Consoles must also be programmed for type, partition number and console

sounder suppression options. Refer to the PROGRAMMING GUIDE (#93 MENU

MODE-DEVICE PROGRAMMING) for instructions.

Note that fiekf wiring to the consoles must be completed before the consoles can

be mounted.

The consoles can be either surface mounted or flush mounted (using an

appropriate Trim Ring Kit: 5137TRK or 6139TRK). Refer to the mounting

instructions and template included with the console and/or trim ring kti for specific

information.

Be sure to take the height of the users into account when mounting consoles.

Consoles may be wired to a single wire run or individual consoles may be

connected to separate wire runs. The maximum wire run length from the panel to

a console which is homerun back to the panel must not exceed:

Wire Guage

Maximum Length

#22gauge

450feet

#20gauge

700feet

#18gauge 1100feet

#16gauge

1750feet

NOTE:The

lengthofall wiremnsoombinadmustnot

excsad2000feetwhenunshieldedquadconductoroabls

isused(1OCOfaatifshieldadtie isused.)

If morethanoneconsoleis wiredto a run,thenthe

abovemaximumlengthsmustbedvkfad thenumber

ofconsolesontherun(i.e.themaximumen thwould

be225

feet iftwo oonsolasarewiredona # 2gauge

Nn),

Up to twelve 4137AD or eight (8) 5137AD or seven (7) 6139 consoles can be

powered from the auxiliafy power output provided that the 750mA rating is not

exceeded. The backup battery will supply power to these consoles in the event

that AC power is lost.

Additional consoles can be connected to the system by using a regulated,

12VDC power supply (eg. 487-12 supplies 12V, 250mA; 488-12 supplies 12V,

500mA). Use a UL Listed, battery backed supply for UL installations. Note that the

maximum number of consoles supported by the system is 16.

Connect additional consoles as shown below, using the console wire colors

shown. Make sure to observe the current ratings for the power supply used.

Wire run lengths from the 4140XMPT2 to consoles are listed in the WIRING

CONSOLES paragraph (maximum combined wire run lengths for all consoles

must not exceed 2000, or 1000 if shielded cable is used).

IMPORTANT: Make connections directly to the screw terminals as shown. Make

no connection to the wnsole blue wire.

The 487-12/488-12 power supplies have a backup battery which can power

these consoles in the event of AC power loss. Note that consoles powered from

supplies which do not have a backup battery will not function when AC power

is lost. In this case, make sure to power at least one console from the Control’s

auxiliary power output.

-31-

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 67 68

Comentarios a estos manuales

Sin comentarios

ADEMCO 4140XMPT2 Manual de usuario Pagina 31

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4140XMPT2