ADEMCO 4140XMPT2 Manual de usuario descargar pdf (Pagina 13)

BASIC 9 HARD-WIRED ZONES

Zone 1

Tha fnllatuinfi tshla m }mm a rivae 7nna i fiharaAnrieibe

I Iw Ivlwwl! 1~ *UUIW Uu$lll Ila# IAUCI &wl IV I WI mmUWLUI *s#J9wu.

Applications

Can be used for EOLR supervised or closed circuit

unsupewised devices. It is the only zone that supports

2-wire smoke detectors.

Zone Response Type: Any

Response Time

350 msec

Max. Zone Resistance 100 ohms, excluding EOLR

Unsupervised Usage

● Cut red PCB jumper.

● Only closed circuit devices can be used.

EOLR Supervised s Leave red PCB jumper intact.

● Supports both open circuit and closed circuit devices.

● Connect open circuit device in parallel across the loop.

The 2,000 ohm EOLR must be connected across the

loop wires at the last device.

● Connect closed circuit device in series with the loop.

EOLR Fire Zone:

● Leave red PCB jumper intact.

● Assgn zone type 09 (fire)

s Supports up to sixteen (16) 2-wire smoke detectors

● Semnd CODE + OFF sequence momentarily

interrupts power to reset the smoke detectors.

● See table below for compatible detectors.

Compatible Smoke Detectors

Detector Type

Device Model #

Photoelectric w/heat sensor, direct wire......................System Sensor 2300T

Photoelectric, direct wire

.........................................

System Sensor 2400

Photoelectric w/heat sensor, direct wire......................System Sensor 2400TH

Photoelectric w/B401B base.....................................

System Sensor 2451

Photoelect. w/heat sensor & B401B base....................System Sensor 2451TH

Ionization, direct wire ..............................................System Sensor 1400

Ionization w/B401B base

.........................................System Sensor 1451

Photoelectric duct detector

wA)H400 base

.......................................................System Senmr2*l

Ionization duct detect. w/DH400 base ........................System Sensor 1451DH

Zone 1 Advisories

If the EOLR is not at the end of the loop, the zone is not properly supervised. The

system may not respond to an open circuit within the zone.

The alarm current provided by this zone is sufficient to supporl operation of only

one detector in the alarmed state.

UL NOTE: EOLR are required for UL installations.

zone 9

The foliowina table summarizes zone 9 characteristics.

Applications This zone is unsupervised and is suitable for monitoring

fast acting glass break sensors or vibration sensors when

orormammed for fast resoonse.

Response Type Any type except fire

Response Time

Normal (350 msec) or Fast (l Omsec)selected in field ●14.

Max. Zone Resistance 300 ohms

Unsupervised Usage

● Only closed circuit devices can be used.

● Connect these devices in series with one another

between terminals 22 & 23.

Zone 9 Advlsorles

Avoid using mechanical magnetic or relay type contacts in this zone when

programmed for fast response.

UL NOTE: The interconnecting wires from zone 9 shall be no longer than 3 feet,

with no interveningwalls or barriers

for UL installations.

-13-

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 67 68

Comentarios a estos manuales

Sin comentarios

ADEMCO 4140XMPT2 Manual de usuario Pagina 13

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO 4140XMPT2