ADEMCO VISTA-250FBP Guia de preparacion descargar pdf (Pagina 9)

– 9 –

*33 PRIMARY PHONE NUMBER

Enter 0-9 for each digit. Enter #11 for *, #12 for #,

#13 for 2-second pause

*34

SECONDARY PHONE NUMBER

Enter 0-9 for each digit. Enter #11 for *, #12 for #,

#13 for 2-second pause

*35

DOWNLOAD PHONE NO.

Enter 0-9 for each digit. Enter #11 for *, #12 for #,

#13 for 2-second pause

*36

DOWNLOAD ID NO.

| | | | | | | |

Enter 00-09; A-F (10-15) [15 15 15 15 15 15 15 15]

*37

DOWNLOAD COMMAND ENABLES

Dlr Shtdwn

Sys Shtdwn

Not Used

Rmt Byp

Rmt Disarm

Rmt Arm

Upld Pgm

Dwnld Pgm

See field 1*53 for Callback disable option; [1=enable];

0=disable. For Commercial Burglary and Commercial Fire

installations, all entries must be "0."

*38 PREVENT ZONE XXX BYPASS [000] | |

001-250; 000 if all zones can be bypassed

*39 ENABLE OPEN/CLOSE REPORT FOR [1]

INSTALLER CODE 1=enable; 0=disable

*40 OPEN/CLOSE REPORT FOR KEYSWITCH [0]

1=enable; 0=disable

*41 NORMALLY CLOSED or EOLR (Zones 3-8) [0]

1=N.C.loops; 0=EOLR supervision.

Must be "0" for Commercial Burglary and Commercial Fire

installations.

*42 DIAL TONE PAUSE [0]

0=5 seconds; 1=11 seconds; 2=30 seconds.

Must be "0" Commercial Burglary and Commercial Fire

installations.

*43 DIAL TONE DETECTION [1]

1=wait for true dial tone; 0=pause, then dial

*44 RING DETECTION COUNT [00] |

01-14; 15=answering machine; 00=no detection.

Must be "00" for Commercial Burglary and Commercial Fire

installations.

*45 PRIMARY FORMAT [1]

0=Low Speed; 1=Contact ID; 2=ADEMCO High Speed;

3= ADEMCO Express

*46 LOW SPEED FORMAT (Primary) [0]

0= ADEMCO Low Speed; 1=Sescoa/Radionics

*47 SECONDARY FORMAT [1]

0=Low Speed; 1=Contact ID; 2= ADEMCO High Speed;

3= ADEMCO Express

*48 LOW SPEED FORMAT (Sec.) [0]

0= ADEMCO Low Speed; 1=Sescoa/Radionics

*49 CHECKSUM VERIFICATION [0] [0]

1=enable; 0=disable Prim Sec

*50 SESCOA/RADIONICS SELECT [0]

1=Sescoa; 0=Radionics

*51 DUAL REPORTING [0]

1=yes; 0=no If used with Spilt Reporting "1" option (1*34),

alarms and alarm restores go to both primary and secondary

numbers, while all other reports go to secondary only. If used

with Split Reporting "2" option, alarms and alarm restores go

to both, open/close and test messages go to secondary only,

while all other reports go to primary. If used with Split

Reporting “3” option, fire alarms and fire restores signals go to

both, all other reports go to secondary only.

*52

STANDARD/EXPANDED REPORT FOR PRIMARY

[0 0 0 0 0 0]

Alarm

Rstr

Byp

Trbl

O/C

LoBat

0=standard; 1=expanded;

NOTE: Expanded overrides 4+2 format.

*53

STANDARD/EXPANDED REPORT FOR SECONDARY

[0 0 0 0 0 0]

Alarm

Rstr

Byp

Trbl

O/C

LoBat

0=standard; 1=expanded;

NOTE: Expanded overrides 4+2 format.

*54 UNATTENDED MODE [1]

0=disable, 1=enable, if automatic downloads will be allowed

Must be "0" for Commercial Fire installations.

*56 DYNAMIC SIGNALING DELAY [03] |

Select the delay time (00-15) times 15 seconds before sending

to second destination.

NOTE: When Communicator is used as a backup to the dialer,

the Dynamic Signaling Delay (*56) should be set to a minimum

of 1 minute.

*57 DYNAMIC SIGNALING PRIORITY [0]

0=Primary dialer; 1=Communicator, as first reporting

destination.

*58 COMM

CENTRAL STATION #1 CATEGORY ENABLE

[0 0 0 0 0 0]

Alarm

Trbl

Byp

O/C

Syst

Test

0=disable, 1=enable for reports for primary subs ID of

communicator.

*59 COMM

CENTRAL STATION #2 CATEGORY ENABLE

[0 0 0 0 0 0]

Alarm

Trbl

Byp

O/C

Syst

Test

0=disable, 1=enable for reports for secondary subs ID of

communicator.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 71 72

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-250FBP Guia de preparacion Pagina 9

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-250FBP