ADEMCO VISTA-250FBP Guia de preparacion descargar pdf (Pagina 38)

– 38 –

PROMPT

EXPLANATION

02 RELAY TYPE

V-PLEX 0

Enter 0 for V-Plex (polling loop) devices. Enter 1 for (ECP) relay modules (4204/4204CF).

Press [✱] to continue.

02 V-PLEX ZONE #

000

For polling loop trigger outputs (4101SN), enter the protection zone number (001-250) linked to each output,

if used. Be sure to enroll the module’s serial number (see Zone Programming).

Press [✱] to continue.

02 ECP ADDRESS

If you selected 1 or 3 for (4204/4204CF), enter the actual module's address (01-15 – 4204/4204CF) as set

by its DIP switches. Up to 8 4204/4204CF modules can be installed in a system.

Press [✱] to continue.

02 MODULE RELAY#

For 4204 Relay Outputs, enter the specific relay number on that module (1-4). For 4204CF outputs,

enter

only module relay number 1 (Output A) or relay number 3 (Output B)

. These are the only two

programmable relays on the 4204CF Module.

Press [✱] to continue.

The keypad will display the Start and Stop summary screens again.

Press [✱] to continue.

When all relays have been programmed, enter 00 at the "ENTER RELAY NO." prompt.

If you are defining a zone list, continue to the next section. If not, enter 00 + [✱] at the next two prompts. You will then be

asked "Quit Menu Mode?" Enter 1 for "Yes," 0 for "No." Then enter ✱99 to exit programming completely.

If supervision of the 4204CF Relay Output is desired, enter a response type for that output's corresponding supervisory zone.

This is equal to 600 + [Relay ID No.]. For example, if you are programming Relay ID No. 1, the relay's supervisory zone 601.

Program this zone with response type 05 (Day/Night) in

Zone Programming

Zone List Programming

After all relays have been programmed, upon entering 00 at the "ENTER RELAY NO." prompt, you are asked to enter a zone

list. If a zone list number was used to start or stop a relay, you must define the zones belonging to that list as follows:

PROMPT

EXPLANATION

ENTER Zn LIST ?

00=QUIT 00

Enter the zone list number 01-15. Enter 00 to quit.

01 ADD ZONE #

000=QUIT 000

Using 3-digit entries enter each zone to be included in this zone list. Press [✱] after you enter each zone

number.

When you have entered all zones, enter 000.

Press [✱] to continue.

01 Del Zn LIST ?

1=YES 0=NO 0

Enter 0 to save this zone list. Enter 1 to delete it.

01 DEL ZONES ?

1=YES 0=NO 0

Enter 1 to delete one or more zones in that zone list. Enter 0 if no changes are necessary. If you enter 1,

the following screen appears; otherwise, the "Enter Zone LIST" prompt reappears.

01 Zn to DELETE ?

000=QUIT 000

Enter each zone number to be deleted from the zone list, pressing [✱] after each number.

VIEW Zn LIST ?

00=QUIT 00

This display appears if you pressed 00 at the “Enter Zone LIST” prompt. Enter the zone list number that you

wish to view.

Press [✱] to continue.

01 ASSIGNED ZONE

000=QUIT 000

Press [✱] to scroll through all zones in that list. Enter 000 +[✱] to quit.

Press [1] to exit Menu Mode.

Press ✱99 to exit Program Mode.

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 71 72

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-250FBP Guia de preparacion Pagina 38

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-250FBP