ADEMCO VISTA-250FBP Guia de preparacion descargar pdf (Pagina 62)

— 62 —

A = DEVICE ACTION 0 = No Response; 1 = Close for 2 sec; 2 = Close and stay closed; 3 = Pulse on and off; 4 =

Toggle alternately between START and STOP events

EV = EVENT 0 = Not used; 1 = Alarm; 2 = Fault; 3 = Trouble; 4 = Restore

ZL = ZONE LIST 01-15, 00 = Not Used

"START" ZONE LIST: Upon alarm, fault, trouble or restore of ANY zone in this list, device

action will START.

"STOP" ZONE LIST: Upon restore of ALL zones on this list, device action will STOP. It

need not be same list as used for START.

ZT = ZONE TYPE/SYSTEM OPERATION

Choices for Zone Type/System Operation are:

00 = No Response (Not Used) 21 = Arming-AWAY**** 41 = AC Power Fail

01 = Entry/Exit #1 22 = Disarming (Code + Off) 42 = System Battery Low

02 = Entry/exit #2 23 = No Alarm Response 43 = Communication failure

03 = Perimeter 44 = RF Low Battery

04 = Interior Follower 45 = Polling Loop Failure

05 = Trouble Day/Alarm Night

27 = Not Used

47 = Console Failure

06 = 24-Hr. Silent 28 = Not Used 51 = RF Receiver Failure

07 = 24-Hr. Audible 29 = Not Used 52 = Kissoff

08 = 24-Hr. Auxiliary 30 = On Second Code + Off 54 = Fire Zone Reset

09 = Fire Alarm or Trouble 31 = End of Exit Time 55 = Disarm + 1 Minute

10 = Interior W/Delay 32 = Start of Entry Time 56 = XX Minutes (enter XX in field 1*74) *

12 = Not Used 33 = Any Burglary Alarm 57 = YY Seconds (enter YY in field 1*75) *

13 = Remote P/S 34 = Code + [#] + 71 58 = Duress

14 = CO Detector Alarm 35 = Code + [#] + 72

16 = Fire With Verification 36 = At Bell Timeout **

17 = Waterflow***** 37 = 2 Times Bell Timeout **

60 = Audio Alarm Verification (must be

selected for both START and STOP

operation)

18 = Fire Supervisory 38 = Chime 61 = Code + [#] + 67

19 = 24-Hour Trouble 39 = Fire Alarm 62 = Bell 2 Timeout

20 = Arming-STAY*** 40 = Bypassing 63 = Auxiliary Relay Timeout

* Stop condition only

** Or at disarming, whichever occurs earlier

*** The output also activates when the partition is armed in the INSTANT mode

**** The output also activates when the partition is armed in the MAXIMUM mode

***** Use an event of fault or alarm as the START option

P = PARTITION No. 1-8, 0 = Any

ZONE LISTS FOR OUTPUT DEVICES – Programmed in the #93 Menu Mode in the Output Programming Section. Fill in the

required data on the worksheet below and follow the procedure shown earlier in this

Programming Guide

as you enter the

data during the displays and prompts that appear in sequence. Up to 15 zone lists may be created

NOTE

Record desired zone numbers below. More or fewer boxes than shown may be needed, as any list may include

any

all

of system's zone numbers.

Zone List 1: Started or stopped by zone numbers (enter 000 to end entries).

Zone List 2: Started or stopped by zone numbers (enter 000 to end entries).

Zone List 3: Started or stopped by zone numbers (enter 000 to end entries).

Zone List 4: Started or stopped by zone numbers (enter 000 to end entries).

1 2 ... 57 58 59 60 61 62 63 64 65 66 67 ... 71 72

Comentarios a estos manuales

Sin comentarios

ADEMCO VISTA-250FBP Guia de preparacion Pagina 62

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO VISTA-250FBP