ADEMCO Security System VISTA-15 Especificaciones descargar pdf (Pagina 63)

SECTION 10

Creating Schedules

•••••••••••••••••••••••••••••••••••••••

About Schedules

The VISTA-20P system provides up to 32 schedules (VISTA-15P supports 8), which can be used to

control 11 types of system events at pre-defined times. Sixteen schedules are intended for use by the

end-user, and sixteen are reserved for the installer (VISTA-15P = 4 user schedules, 4 installer

schedules). In addition, some events are also reserved for the installer only (listed in the “Enter Event”

prompt paragraph below).

Start Scheduling mode by entering installer code + [#] + [6] [4] while in normal operating mode.

NOTE: The master code can only access schedules 01-16 (VISTA-15P = 01-04) and events 00-07.

The following prompts are displayed:

PROMPT VALID ENTRIES EXPLANATION

ENTER SCHED NO.

00=QUIT 00

Schedule Number

VISTA-20P

01-16 = end-user schedules

17-32 = installer-only schedules

VISTA-15P

01-04 = end-user schedules

05-08- = installer-only schedules

[

∗

] to continue

Enter the desired schedule number.

ENTER EVENT

NOTE:

Events 07 and

10 cause the keypad to

beep every 30 seconds

when messages are

displayed. Stop the

beeps by user code +

OFF.

Enter Event

00 = clear event

01 = Relay On/Off

02 = User Access

03 = Latch Key Report to Pager

04 = Forced Stay Arming

†

05 = Forced Away Arming

†

06 = Auto Disarm

07 = Display “Reminder”

10 = Display custom words

††

11 = Periodic Test Report

†††

[

∗

] to continue

Enter the desired event number for event you want to occur at a

specified time.

Events 10-11 are reserved for the installer only.

Latch key report (option 03) is sent to all pagers in the user’s

partition (message sent is 777-7777). User must be enabled for

paging (see User Attributes in

System Operation

section).

†

Forced bypass is automatically enabled regardless of setting in field

*23.

††

if selected, system displays custom words 8, 9, and 10 at defined

time. Can be used as installer’s reminder message to the end user.

†††

see key commands in

Testing the System

section to

quickly set periodic test reporting intervals

DEVICE NUMBER

Device Number

01-18 = device number

[

∗

] to continue

This prompt appears if event “1” (relay on/off) was selected, otherwise

it is skipped.

Enter the physical device number as programmed in

∗

79 Menu Mode,

then press [*] to continue to the “Start” prompt.

Device numbers 17 and 18 designate built-in triggers 1 and 2

respectively.

GROUP NUMBER

Group Number

1-8 = group number

[

∗

] to continue

This prompt appears if event “2” (user access) was selected.

Otherwise it is skipped.

Press [*] to continue to the “Start” prompt.

PARTITION

Partition

0 = all partitions

1 = partition 1

2 = partition 2

3 = common

[

∗

] to continue

This prompt appears if events “3-7,10,12” were selected. Otherwise it

is skipped.

Press [*] to continue to the “Start” prompt.

10-1

1 2 ... 58 59 60 61 62 63 64 65 66 67 68 ... 87 88

Comentarios a estos manuales

Sin comentarios

ADEMCO Security System VISTA-15 Especificaciones Pagina 63

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad ADEMCO Security System VISTA-15